Product description
Arduino MKRFOX1200 has been designed to offer a practical and cost effective solution for makers seeking to add SigFox connectivity to their projects with minimal previous experience in networking.
It is based on the Microchip SAMD21 and a ATA8520 SigFox module.
MKRFOX1200 can run for over six months on 2 AA 1.5V batteries with typical usage.
The design includes the ability to power the board using two 1.5V AA or AAA batteries or external 5V. Switching from one source to the other is done automatically.
A good 32-bit computational power similar to the Zero board, the usual rich set of I/O interfaces, low power SigFox communication and the ease of use of the Arduino Software (IDE) for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor.
The USB port can be used to supply power (5V) to the board.
The Arduino MKRFOX1200 is able to run with or without the batteries connected and has limited power consumption.
Warning: Unlike most Arduino & Genuino boards, the MKRFOX1200 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.
If you want more informations on SIGFOX please visit makers.sigfox.com and ask.sigfox.com
* Microcontroller: SAMD21 Cortex-M0+ 32bit low power ARM MCU
* Board Power Supply (USB/VIN): 5V
* Supported Batteries: 2x AA or AAA
* Circuit Operating Voltage: 3.3V
* Digital I/O Pins: 8
* PWM Pins: 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19)
* UART: 1
* SPI: 1
* I2C: 1
* Analog Input Pins: 7 (ADC 8/10/12 bit)
* Analog Output Pins: 1 (DAC 10 bit)
* External Interrupts: 8 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17)
* DC Current per I/O Pin: 7mA
* Flash Memory: 256kB
* SRAM: 32KB
* EEPROM: no
* Clock Speed: 32.768kHz (RTC), 48MHz
* Antenna power: 2dB
* Carrier frequency: 868MHz
* Working region: EU
* Length: 67.64mm
* Width: 25mm
* Weight: 32g
It is based on the Microchip SAMD21 and a ATA8520 SigFox module.
MKRFOX1200 can run for over six months on 2 AA 1.5V batteries with typical usage.
The design includes the ability to power the board using two 1.5V AA or AAA batteries or external 5V. Switching from one source to the other is done automatically.
A good 32-bit computational power similar to the Zero board, the usual rich set of I/O interfaces, low power SigFox communication and the ease of use of the Arduino Software (IDE) for code development and programming. All these features make this board the preferred choice for the emerging IoT battery-powered projects in a compact form factor.
The USB port can be used to supply power (5V) to the board.
The Arduino MKRFOX1200 is able to run with or without the batteries connected and has limited power consumption.
Warning: Unlike most Arduino & Genuino boards, the MKRFOX1200 runs at 3.3V. The maximum voltage that the I/O pins can tolerate is 3.3V. Applying voltages higher than 3.3V to any I/O pin could damage the board. While output to 5V digital devices is possible, bidirectional communication with 5V devices needs proper level shifting.
If you want more informations on SIGFOX please visit makers.sigfox.com and ask.sigfox.com
* Microcontroller: SAMD21 Cortex-M0+ 32bit low power ARM MCU
* Board Power Supply (USB/VIN): 5V
* Supported Batteries: 2x AA or AAA
* Circuit Operating Voltage: 3.3V
* Digital I/O Pins: 8
* PWM Pins: 12 (0, 1, 2, 3, 4, 5, 6, 7, 8, 10, A3 - or 18 -, A4 -or 19)
* UART: 1
* SPI: 1
* I2C: 1
* Analog Input Pins: 7 (ADC 8/10/12 bit)
* Analog Output Pins: 1 (DAC 10 bit)
* External Interrupts: 8 (0, 1, 4, 5, 6, 7, 8, A1 -or 16-, A2 - or 17)
* DC Current per I/O Pin: 7mA
* Flash Memory: 256kB
* SRAM: 32KB
* EEPROM: no
* Clock Speed: 32.768kHz (RTC), 48MHz
* Antenna power: 2dB
* Carrier frequency: 868MHz
* Working region: EU
* Length: 67.64mm
* Width: 25mm
* Weight: 32g
