Produktbeskrivning
Multimeter-kit för mätning upp till 50VDC. OBS! Endast för DC och endast mellan 0-50VDC, ingen negativ spänning.
The Multimeter Kit provides you with everything you need to make your own multimeter capable of measure voltage (0-50VDC, 0.05 resolution) current (0-500mA, 1mA resolution) and resistance (0-100kO). The resistance mode also includes a continuity test: the buzzer will sound when the resistance probes are shorted together, this is one of the more handy tools of any multimeter.
Using the Multimeter Kit is very straightforward. To measure voltage connect your probes to the 'Voltage' and 'Common' pins, for current measurement the 'Current' and 'Common' pins. Resistance measurement uses the 'Res-1' and 'Res-2' pins. The decimal points are used in resistance measurement mode to indicate 10kO and 100kO ranges.
The kit doesn't include probes, but you have the option of using banana plug test cables or you can solder simple jumper wires into the smaller probe inputs.
Please note: using the resistance measurement mode on live circuits is not recommended. Also, do not test current or voltage on devices that may be outside the measuring range (no negative voltages or currents)! The multimeter is very simple, and won't replace your Fluke meter, but it works perfectly for simple troubleshooting.
Batteries not included.
Kit Includes:
1x Multimeter Kit PCB
1x ATMega328 programmed for Multimeter Kit
1x LM358 Op-Amp
1x 3.3V Voltage Regulator
1x Red 4-Digit 7-Segment Display
1x Buzzer 2.048 KHz
1x Battery Holder Pack AA x 4
1x 100uF Capacitor
1x 10uF Capaciator
2x 1.0kO Resistor
2x 10kO Resistor
1x 5.6kO Resistor
1x 1.2kO Resistor
1x 1.0O Resistor
1x SPDT Mini Power Switch
1x Push Button Switch
The Multimeter Kit provides you with everything you need to make your own multimeter capable of measure voltage (0-50VDC, 0.05 resolution) current (0-500mA, 1mA resolution) and resistance (0-100kO). The resistance mode also includes a continuity test: the buzzer will sound when the resistance probes are shorted together, this is one of the more handy tools of any multimeter.
Using the Multimeter Kit is very straightforward. To measure voltage connect your probes to the 'Voltage' and 'Common' pins, for current measurement the 'Current' and 'Common' pins. Resistance measurement uses the 'Res-1' and 'Res-2' pins. The decimal points are used in resistance measurement mode to indicate 10kO and 100kO ranges.
The kit doesn't include probes, but you have the option of using banana plug test cables or you can solder simple jumper wires into the smaller probe inputs.
Please note: using the resistance measurement mode on live circuits is not recommended. Also, do not test current or voltage on devices that may be outside the measuring range (no negative voltages or currents)! The multimeter is very simple, and won't replace your Fluke meter, but it works perfectly for simple troubleshooting.
Batteries not included.
Kit Includes:
1x Multimeter Kit PCB
1x ATMega328 programmed for Multimeter Kit
1x LM358 Op-Amp
1x 3.3V Voltage Regulator
1x Red 4-Digit 7-Segment Display
1x Buzzer 2.048 KHz
1x Battery Holder Pack AA x 4
1x 100uF Capacitor
1x 10uF Capaciator
2x 1.0kO Resistor
2x 10kO Resistor
1x 5.6kO Resistor
1x 1.2kO Resistor
1x 1.0O Resistor
1x SPDT Mini Power Switch
1x Push Button Switch