ARM

STM32-H103 utvecklingskort Cortex-M3

Art.nr: 41010595
Tillverkare: Olimex
I lager: 3

Beskrivning

STM32-H103 HEADER BOARD FOR STM32F103RBT6 CORTEX-M3 MICROCONTROLLER

The ARM Cortex-M3 processor is the latest generation of ARM processors for embedded systems. It has been developed to provide a low-cost platform that meets the needs of MCU implementation, with a reduced pin count and low-power consumption, while delivering outstanding computational performance and an advanced system response to interrupts. The ARM Cortex-M3 32-bit RISC processor features exceptional code-efficiency, delivering the high-performance expected from an ARM core in the memory size usually associated with 8- and 16-bit devices.

The STM32F103 Performance Line family has an embedded ARM core and is therefore compatible with all ARM tools and software. It combines the high performance ARM Cortex-M3 CPU with an extensive range of peripheral functions and enhanced I/O capabilities. STM32-H103 is low cost development board for the new ST Cortex-M3 based microcontrollers STM32F103RBT6. This board is perfect solution for USB peripherials development. All microcontroller ports are available on extension connectors.

FEATURES:

MCU: STM32F103RBT6 ARM 32 bit CORTEX M3 with 128K Bytes Program Flash, 20K Bytes RAM, USB, CAN, x2 I2C, x2 ADC 12 bit, x3 UART, x2 SPI, x3 TIMERS, up to 72Mhz operation

standard JTAG connector with ARM 2x10 pin layout for programming/debugging with ARM-JTAG

USB connector

user button

RESET button

status LED

power supply LED

on board voltage regulator 3.3V with up to 800mA current

single power supply: takes power from USB port or extension connector pin

8 Mhz crystal oscillator

32768 Hz crystal and RTC backup battery connector

extension headers for all uC ports

PCB: FR-4, 1.5 mm (0,062"), soldermask, silkscreen component print

Dimensions: 61x 34mm (2.4 x 1.3")

Distance between the exntension connectors: 25.4 mm (1")

Kunder som köpte den här köpte ocksåKunder köpte också

  • ARM-USB-OCD-H 3-in-1 ARM debgger/programmer hi-speed

      ARM-USB-OCD-H 3-in-1 ARM debgger/programmer hi-speed
    FEATURES First on market three-in-one USB JTAG debugger - offers JTAG + RS232 (full modem signals supported) port + power supply all in one compact device High speed USB 2.0 JTAG dongle interface, can be used with all ARM devices for programming and debugging. uses ARM's standard 2x10 pin JTAG connector supports ARM targets working in voltage range 1.65 5.0 V DC supports adaptive clocking RTCK software supported by OpenOCD (open source) debugger adds virtual RS232 port to your computer with all modem signals like: DTR, DSR, DCD, RTS, CTS, Rx, Tx Can be used as power supply to your target board with 5V USB source current is limited with resettable fuse at 300mA, at the different output voltage the maximum current is different: 5V/200mA, note that this also depend on your USB host current capabilities, if other USB devices are attached to your computer or if the laptop is running on batteries these figures may be different and depend on your computer USB host. Downloadable Windows installer for full featured and open source tools as alternative to the commercial ARM development packages: GCC C compiler, openOCD debugger and Eclipse IDE. Works with IAR EW-ARM 5.50 or newer Dimensions 50x40 mm (2x1.6") + 20 cm (8") JTAG cable + 30 cm (12") power supply cable FAQ: Q: Can I use ARM-USB-OCD-H with EW-ARM? A: IAR supports GDB and works with ARM-USB-OCD-H Q: I use Windows XP x64, how I can update the USB drivers? A: FTDI have x64 drivers on their web, download them and use our ARM-USB-OCD PID: 0x0003, VID: 0x15BA to install the drivers. Q: how to install ARM-USB-OCD-H to work with CrossWorks: Use: "Generic FTD2232" target interface 1. Right click on a blank space in the targets window and select "New Target Interface > Generic FT2232 Device". 2. Right click on the new target interface and select "Properties" - set the following properties: Connected LED Inversion Mask 0x0000 Connected LED Mask = 0x0800 nSRST Inversion Mask = 0x0200 nSRST Mask = 0x0200 nTRST Inversion Mask = 0x0000 nTRST Mask = 0x0100 Output Pins = 0x0F1B Output Value = 0x0D08 Running LED Inversion Mask = 0x0000 Running LED Mask = 0x0800 It is recommended to use LibUSB drivers instead of FTDI PID: 0x002B VID: 0x15BA In CrossWorks 1.7 there are Target interfaces for Olimex JTAGs, note that RTCK is not used with FT2232 design so your JTAG clock should not exceed 1/6 of your target MCU clock or the JTAG will lock up, start with JTAG divider 10 and decrease until you are able to debug to find your own value for your target. Q: Can I debug high voltage targets with ARM-USB-OCD-H? A: ARM-USB-OCD-H is not isolated, but you can use USB-ISO isolator device to protect your PC while debugging high voltage targets.
    Art.nr: 41010224
    I lager: 2 
    599.00

  • ARM-JTAG-20-10 JTAG adapter

      ARM-JTAG-20-10 JTAG adapter
    ARM-JTAG-20-10 JTAG 20 PIN 0.1" TO 10 PIN 0.05" ADAPTER FEATURES Plug-in adapter for ARM-USB-OCD, ARM-USB-OCD-H, ARM-USB-TINY, ARM-USB-TINY-H which allow ARM processors which support SWD (like LPC1343) to be programmed/debugged dimensions 50x40 mm (2x1.6") + 20 cm (8") JTAG cable 0.05"step
    Art.nr: 41010594
    Tillfälligt slut
    59.00

  • Logic sniffer kabelsats

      Logic sniffer kabelsats
    Kabel med 9 st clips. 2 kablar behövs för 16 kanaler.
    Art.nr: 41004257
    I lager: 4 
    84.00

  • Labsladd 0.64mm-0.64mm hona/hona 100mm set om 10st

      Labsladd 0.64mm-0.64mm hona/hona 100mm set om 10st
    Kopplingssladdar (jumpers) för 0.64mm fyrkantsstift. Längd 100 mm. Levereras i set om 10 st i 5 olika färger.
    Art.nr: 41002891
    I lager: 6 
    1 - 36.00
    10 - 32.40
    25 - 27.00

  • ARM-USB-OCD 3-in-1 ARM debgger/programmer

      ARM-USB-OCD 3-in-1 ARM debgger/programmer
    Description: This is the mother of all JTAG Programmers for ARMs - and it's about 1/10th the price of other programmer/debuggers with the same functionality! Features: First on market three-in-one USB JTAG debugger - offers JTAG + RS232 (full modem signals supported) port + power supply all in one compact device Fast speed USB 2.0 JTAG dongle interface, can be used with all ARM devices for programming and debugging. Uses ARM's standard 2x10 pin JTAG connector Supports ARM targets working in voltage range 2.0 5.0 V DC Software supported by OpenOCD (open source) debugger adds virtual RS232 port to your computer with all modem signals like: DTR, DSR, DCD, RTS, CTS, Rx, Tx Can be used as power supply to your target board with three jumper selectable power supplies: 5V 9V and 12VDC, USB source current is limited with resetable fuse at 300mA, at the different output voltage the maximum current is different: 5V/200mA, 9V/100mA, 12V/70mA, note that this also depend on your USB host current capabilities, if other USB devices are attached to your computer or if the laptop is running on batteries these figures may be different and depend on your computer USB host. Comes with CD with Windows installer for full featured and open source tools as alternative to the commercial ARM development packages: GCC C compiler, openOCD debugger and Eclipse IDE. Dimensions: 50x40 mm (2x1.6") + 20 cm (8") JTAG cable + 30 cm (12") power supply cable
    Art.nr: 41002951
    Tillfälligt slut
    599.00

  • PT-100 givare

      PT-100 givare
    PT-100 givare med linjär karakteristik Rekomenderad ström vid mätning är kring 1mA Fabrikat: Jumo Typbenämning: 00089203 Mätområde: -70-400°C Mått(LxBxH): 10x2x1.3mm
    Art.nr: 41011664
    I lager: 10 
    48.00