TinkerKit Rotary potentiometer

Part.no: 41012645
In stock: 11

Description

A Potentiometer is a commonly used variable resistor. Turning the knob, you vary the output voltage between 0 and 5V. This value is sent through the middle pin of the pot.

Output: This module outputs 5v when turned in one direction, and 0v when turned in the opposite way. When connected to an input on the Arduino using the TinkerKit Shield, you can expect to read values between 0 and 1023.

Module Description: This module features a 4k7 Ohm linear potentiometer, a signal amplifier, the standard TinkerKit 3pin connector, a green LED that signals that the module is correctly powered and a yellow LED whose brightness changes according to the position of the potentiometer.

Customers Who Bought This Item Also BoughtCustomers Also Bought

  • TinkerKit Sensor Shield v.2

      TinkerKit Sensor Shield v.2
    The Sensor Shield v.2 allows you to hook up the TinkerKit SENSORS and ACTUATORS directly to the Arduino, without the use of the breadboard. It has 12 standard TinkeKit 3pin connectors. The 6 labeled I0 through I5 are Analog Inputs. The ones labeled O0through 05 are Analog Outputs connected to the PWM capable outputs of the Arduino Board (it is possible to change these to Digital Inputs, in which case they will report either HIGH or LOW, but nothing in between). Pin 11 on the Arduino is O0 on the shield. Pin 10 on the Arduino is O1 on the shield. Pin 9 on the Arduino is O2 on the shield. Pin 6 on the Arduino is O3 on the shield. Pin 5 on the Arduino is O4 on the shield. Pin 3 on the Arduino is O5 on the shield. Module description: A green LED signals that the shield is correctly powered, a standard 6mm pushbutton allows you to RESET the board. The 4pin TWI socket allows communication to any device supporting the I2C protocol through the Wire library on Arduino. 5V and Ground are provided on the socket. Note that on Arduino the I2C bus uses Analog Input 4 and 5, using the TWI connection precludes the use of those analog inputs. The 4pin SERIAL socket allows the board to communicate with other devices that support serial communication. 5V and Ground are provided on the socket for your convenience. Note: If you are sending or receiving data to and from the computer this serial connector is not available. Two mounting holes are provided in the same position found on the Arduino board. A third hole allows you to see the led connected to pin 13 of the Arduino.
    Part.no: 41012662
    Currently not in stock
    $16.75

  • TinkerKit Cable 3-pin 50cm

      TinkerKit Cable 3-pin 50cm
    Wire for the TinkerKit with a 3 pin jumper on both sides. BLACK is ground; ORANGE is signal; RED is power (5V);
    Part.no: 41012653
    Currently not in stock
    $2.29

  • TinkerKit Cable 3-pin 20cm

      TinkerKit Cable 3-pin 20cm
    Wire for the TinkerKit with a 3 pin jumper on both sides. BLACK is ground; ORANGE is signal; RED is power (5V);
    Part.no: 41012652
    In stock: 5 
    Buy
    $1.81

  • TinkerKit Push button

      TinkerKit Push button
    The Pushbutton Module is possibly the simplest sensor available. It detects when a person or an object presses on its circular cap. Output:This module outputs 5v when the button is pressed and 0v when released. Pressing the button closes the circuit. When connected to an input on the Arduino using the TinkerKit Shield, you can expect a value of 1023 while the button is pressed and 0 when released. Module Description: This module features a 12mm pushbutton , the standard TinkerKit 3pin connector, a green LED that signals that the module is correctly powered and a yellow LED that is lit only when the button is pressed. This module is a SENSOR. The connector is an OUTPUT which must be connected to one of the INPUT connectors on the TinkerKit Shield.
    Part.no: 41012646
    In stock: 82 
    Buy
    $5.42

  • TinkerKit Cable 3-pin 100cm

      TinkerKit Cable 3-pin 100cm
    Wire for the TinkerKit with a 3 pin jumper on both sides. BLACK is ground; ORANGE is signal; RED is power (5V);
    Part.no: 41012654
    Currently not in stock
    $3.49