TinkerKit Analog Joystick

Part.no: 41012642
In stock: 8

Description

The Joystick module is similar to analog joysticks found in gamepads. It is made made by mounting two potentiometers at a 90 degrees angle. The potentiometers are connected to a short stick centered by springs.

Output: This module will output roughly 2.5 volts from both outputs when in its resting position. Moving the stick will cause the outputs to change from 0v to 5v depending on its direction. If you connect this module to an Arduino through the Tinkerkit Shield, you can expect to read a value of roughly 512 in its resting position (expect small variations due to tiny imprecisions of the springs and mechanism) When you move the joystick you should see the values change from 0 to 1023 depending on its position.

Module Description: This module features two 4k7 Ohm linear potentiometers, two standard TinkerKit 3pin connector, two signal amplifiers, a green LED that signals that the module is correctly powered and two yellow LED whose brightness depends on the values output by the module.

Customers Who Bought This Item Also BoughtCustomers Also Bought

  • TinkerKit Accelerometer 2/3 axis

      TinkerKit Accelerometer 2/3 axis
    An accelerometer is a device that measures acceleration. It is very common in consumer electronics such as portable electronic devices and video game controllers to detect movement using accelerometers. Output: This module outputs 0V to 5V on one of its two signal pins when its G-force is changed (e.g. is moved). The value is approximately 2.5V when there is 0G on the X or Y axis. When you connect this module to the input on an Arduino using the TinkerKit Shield, you can expect to read values between 0 to 1023 while moving the module. Module description: On the back of the module you can find two signal amplifier and a green LED that signals that the module is correctly powered. The module is based on the LIS344AL by ST Microelectronics, and is a three-axis acceremoter. You can get data about the third axis (referred to as Z) by soldering a header to the thru-hole labeled Z.
    Part.no: 41012656
    In stock: 13 
    Buy
    $19.16

  • TinkerKit Rotary potentiometer

      TinkerKit Rotary potentiometer
    A Potentiometer is a commonly used variable resistor. Turning the knob, you vary the output voltage between 0 and 5V. This value is sent through the middle pin of the pot. Output: This module outputs 5v when turned in one direction, and 0v when turned in the opposite way. When connected to an input on the Arduino using the TinkerKit Shield, you can expect to read values between 0 and 1023. Module Description: This module features a 4k7 Ohm linear potentiometer, a signal amplifier, the standard TinkerKit 3pin connector, a green LED that signals that the module is correctly powered and a yellow LED whose brightness changes according to the position of the potentiometer.
    Part.no: 41012645
    In stock: 7 
    Buy
    $5.90

  • Ibridge 4x4 keypad shield with LCD interface

      Ibridge 4x4 keypad shield with LCD interface
    IBridge is a 4X4 key-pad shield with a 5110 Graphic LCD interface. It is compatible with Arduino and IFLAT-32, you can plug it on Arduino/IFLAT-32 board directly, and you can get the small development platform with keypad input and LCD must be purchased separately.
    Part.no: 41010161
    In stock: 2 
    Buy
    $11.93

  • Motion sensor IR

      Motion sensor IR
    Features * small and compact unit * operate output relay by waving hand or object in front of unit * no touching required * adjustable sensitivity * status led indicators * momentary (pulse) or toggle (ON/OFF) mode * Perfectly suited for our Velbus system and our K8006 home bus system * Use for detection in DIY projects (not suited for very dark object detection) * Comes complete with snap-in enclosure. Type VMBFBI * fits Velleman VMBFDG and VMBFLG frames Specifications * power supply: max. 12VDC/100mA * output relay rating: 3A/24VDC * LED indication * dimensions (wxhxd): 21x47x41mm / 0.8x1.85x1.6"
    Part.no: 12008092
    In stock: 2 
    Buy
    $32.41

  • Solder flux liquid 50ml

      Solder flux liquid 50ml
    Flux multicore X32-10i Contains isopropyl alcohol (30-100%) Non-corrosive, halogen free flux. Short whetting time Can function as flux foam in wave soldering machines Fast-drying, leaves no residue. Comes in 50mL plastic bottle.
    Part.no: 41010675
    In stock: 18 
    Buy
    $4.70