Motor control

Showing 1 to 28 of 28 matching products
Sort by
 
  • Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A

      Adafruit DRV8871 DC Motor Driver Breakout Board - 3.6A
    Crank up your robotics with powerful Adafruit DRV8871 motor driver breakout board. This motor driver has a lot of great specs that make it useful for a wide variety of mechatronics. In particular, the simple resistor-set current limiting and auto-magic PWM support make it super easy to use with just about any brushed DC motor. Check out the specs for the DRV8871: 6.5V to 45V motor power voltage Up to 5.5V logic level on IN pins 565mO Typical RDS(on) (high + low) 3.6A peak current PWM control Current limiting/regulation without an inline sense resistor Undervoltage lockout Overcurrent protection Thermal shutdown Using it is super simple. Connect your motor to the OUT terminal block. Power the board with 6.5-45VDC power on VMotor and provide the H-bridge input control on IN1 and IN2. You can even PWM the inputs and the driver chip will do the right thing. You can set the current limiting with an external resistor Rlim. We solder in a 30K resistor by default for a ~2A current limit, however you can remove this resistor and/or solder a resistor over it to change the resistance and change the limit. Each order comes with one fully assembled and tested motor driver breakout, two 2-pin terminal blocks and a small strip of header. Some light soldering is required to attach the header and terminal blocks but its a simple task that can be done with basic soldering equipment.
    Part.no: 41015431
    In stock: 27 
    Buy
    $11.93

  • AutoDriver - L6470 Bipolar stepper motor driver SPI

      AutoDriver - L6470 Bipolar stepper motor driver SPI
    This AutoDriver makes it easy to put the L6470 Stepper Driver (a.k.a dSPIN) to work in your project. Simply connect your motors and your SPI-capable microcontroller and get steppin'! STMicros L6470 is a 3A, 8-45V bipolar stepper motor driver. It has built-in overcurrent detection, undervoltage detection, overtemperature detection, stall detection, a 5-bit ADC, and a switch input that can be used for either user jog control or as a hard stop function. As if that werent enough, it also features microstepping support (up to 128 microsteps per full step) and PWM drive voltage limiting. Unlike most stepper motor drivers, the dSPIN is controlled over an SPI link. It has an on-board 16MHz oscillator which allows it to autonomously execute movement commands. That means no more counting steps in your code! It also supports customized acceleration and deceleration profiles to prevent jerky starts and stops. On-board registers track current speed and location. The logic supply voltage supports both 3.3V and 5V I/O levels. Features: Supports up to 128 Microsteps per Full Step Over-Temperature Detect Over-Current Detect Under-Voltage Detect PWM Drive-Voltage Limiting SPI Controlled On-Board Oscillator and Speed/Location Registers Stall Detection 5-bit ADC
    Part.no: 41013135
    In stock: 2 
    Buy
    $44.46

  • Big Easy Driver

      Big Easy Driver
    Its the next version of the popular Easy Driver board. The Big Easy Driver, designed by Brian Schmalz, is a stepper motor driver board for bi-polar stepper motors up to a max 2A/phase. It is based on the Allegro A4988 stepper driver chip. Each Big Easy Driver can drive up to a max of 2A per phase of a bi-polar stepper motor. It is a chopper microstepping driver which defaults to 16 step microstepping mode. It can take a maximum motor drive voltage of around 35V, and includes on-board 5V/3.3V regulation, so only one supply is necessary. Although this board should be able to run most systems without active cooling while opperating at 1.7A/phase, a heatsink is recommended for loads approaching 2A/phase. You can find the recommended heatsink in the related items below. Features: Bi-polar Microstepping Driver 2A/Phase Max Max Motor Drive Voltage: 35V On-board 5V/3.3V Regulation Note: This product is a collaboration with Brian Schmalz. A portion of each sales goes back to him for product support and continued development.
    Part.no: 41013617
    In stock: 8 
    Buy
    $26.39

  • DC motor controller Roboclaw 2x7A

      DC motor controller Roboclaw 2x7A
    The RoboClaw 2x7A motor controller by Ion Motion Control can supply two brushed DC motors with 7.5 Amps continuous and up to 15 Amps peak. With its multi mode interface it can be controlled from USB, RC radio, serial devices, analog and or microcontrollers such as an Arduino or Raspberry Pi. Dual quadrature encoders with up to 19.6 million pulses per second are supported. In addition, a wide range of sensor inputs including potentiometers and absolute encoders are supported. RoboClaw's close loop functionality creates absolute control over speed, velocity and direction regardless of loading changes. At the heart of RoboClaw is a high performance motion control intelligence which achieves high precision control and optimum motor performance in open or closed loop modes. With RoboClaw's synchronous regenerative capabilities it will charge a supply battery during slow down or breaking action. With it's advance circuitry it can also change direction during full throttle without damage! RoboClaw also incorporates a lithium cutoff mode protecting batteries from damage. Features: - USB Interface - 3.3V Compliant Outputs - 5V Tolerant Inputs - Quadrature Encoders - Absolute Encoders - Position and Velocity Control - Encoders Supported in all Modes - High Resolution Current Sense - High Speed Direction Change - 5V 3A Switch Mode BEC - Battery Level Monitoring - Dual Channel Quadrature Decoding - Dual 19,600,000 PPS Per Channel - Thermal Protection - Regenerative Breaking - Serial, RC or Analog Control - Easy to Use - Can be Bussed
    Part.no: 41015436
    In stock: 2 
    Buy
    $144.46

  • DC motor module

      DC motor module
    Module with driver and dc-motor it contains 2 fork couplers
    Part.no: 41010555
    In stock: 21 
    Buy
    $23.98

  • DC motor speed control 15A

      DC motor speed control 15A
    Powerful DC-motor controller. This module can control motor speed from 0% to 100% at loads up to 15A. Power supply: 12-24 VDC. Load voltage: 12-24VDC./30A. max. Motor speed: Pulse Witdh Modulation (PWM) for controlling motor speed. PCB dimension : 83.3 x 46.2 mm (3.28 x 1.82")
    Part.no: 12108033
    In stock: 34 
    Buy
    $33.68

  • DC motor speed control 30A

      DC motor speed control 30A
    Powerful DC-motor controller. This module can control motor speed from 0% to 100% at loads up to 30A. Power supply: 12-24 VDC. Load voltage: 12-24VDC./30A. max. Motor speed: Pulse Witdh Modulation (PWM) for controlling motor speed. Output frequency : 100Hz. PCB dimension : 97.7 x 40.4 mm (3.85 x 1.59")
    Part.no: 12108066
    In stock: 2 
    Buy
    $25.66

  • DC motor speed control 30A adj freq

      DC motor speed control 30A adj freq
    DC motor speed controller. The controller works by pulse width modulation. The frequency is adjustable between 400Hz and 3kHz. Supply voltage: 8-30VDC Max load: 30A
    Part.no: 12108067
    In stock: 5 
    Buy
    $45.54

  • DC motor speed control 50A adj freq

      DC motor speed control 50A adj freq
    PWM generator för hastighetsreglering av DC-motorer. 8-30V DC Max 50A Frekvens 100Hz fast eller variabel 400Hz-3kHz Kraftig kylfläns för god kylning Anslutning till motor: flatstift 6.3mm Dimensioner (inkl. kylfläns): 87 x 125 x 45mm
    Part.no: 12108068
    In stock: 13 
    Buy
    $84.22

  • DC motor speed controller / LED dimmer 15V 0.5A

      DC motor speed controller / LED dimmer 15V 0.5A
    Module for speed control of DC-motors or for dimming LEDs. Works by pulse-width modulation (PWM). Built around a 555-timer IC. Max load: 6-15 V / 500mA Also available as DIY-kit, art-no; 12100804
    Part.no: 21200804
    In stock: 14 
    Buy
    $16.75

  • DC motor speed controller 30A with soft-start

      DC motor speed controller 30A with soft-start
    This uniquely designed circuit uses IC microcontroller for controlling the operation with a built-in soft-start to prevent electric shock. In addition, voltage control and mosfet driver circuits are provided to increase working efficiency in both high and low frequency plus resistant to noisy signal. Technical specifications - Motor speed : Using IC microcontroller PWM (Pulse With Modulation) for motor speed control. - Built-in soft start for protecting electric shock when supply the voltage. - There is the limit voltage circuit at the gate of mosfet for protecting the over voltage and noisy signal. - Using the mosfet driver circuit to greatly increase working efficiency of the circuit in the low-high frequency to 12.8kHz. - Power supply : 8-30VDC. (select by jumper and motor). - Load voltage : 8-30VDC./ 30A. max. - PWM duty cycle : adjustable from 0% to 100%. - PCB dimensions : 3.83 x 1.57 in.
    Part.no: 12108089
    Currently not in stock
    Buy
    $39.64

  • DC motor speed controller PWM 12-50V 5A (assembled)

      DC motor speed controller PWM 12-50V 5A (assembled)
    This is a speed control circuit for a DC motor. Not only the speed of the motor can be controlled but the frequency also adjustable.(due to the application of Pulse Width Modulation technique). Specifications: * Power supply : 12-50VDC. (jumper selection). * Load voltage : 12-50VDC./ 5A. max. * Motor speed (PWM) can be adjusted from 0% to 100%. * Can be adjusted frequency 3 ranges (jumper selection): 1. 50Hz - 1kHz. - 2. 240Hz - 13.84kHz. - 3. 1.9kHz - 100kHz. * IC board dimension : 3.01 in x 1.83 in.
    Part.no: 21200823
    Currently not in stock
    Buy
    $23.98

  • DC motorstyrning 30A digital

      DC motorstyrning 30A digital
    Powerful, digital motor driver module for DC-motors. MOSFET drivers for high efficiency. Built-in soft start. The controller board has buttons for manually setting the motor speed and for storing and recalling preset speeds. Supply voltage: 12/24VDC Load voltage: 12/24VDC. / 30A. max. Motor speed: Pulsbreddsmodulering (PWM) för motorhastighet Speed recording level: 3 levels??? Soft start: 1 second Moduleringshastighet: 100Hz, 500Hz, 1kHz, 2kHz, 4kHz och 8kHz Duty cycle: Styrbar från 0% till 100% Dimensions: 87.12 mm x 39.11 mm (3.43 x 1.54")
    Part.no: 12108087
    In stock: 4 
    Buy
    $48.07

  • Driver for stepper motors ULN2003A

      Driver for stepper motors ULN2003A
    Driver based around the ULN2003A darlington array. The board connects directly to a microcontroller and drives a connected stepper motor by sending alternating pulses to the motor. The onboard LEDs shows the drive signals. Works with the stepper motors 41010630 and 41010629. * Supply voltage: 5 - 12VDC * Max drive current: 500mA (per outout) * Dimensions: 29 x 21mm
    Part.no: 41015762
    In stock: 96 
    Buy
    $5.90

  • EasyDriver v4 step motor driver

      EasyDriver v4 step motor driver
    En modul för att driva stegmotorer från digital utrustning. Ingången skall vara en digital 0-5V puls, och utgången kan driva stegmotorer med 7-30V matningsspänning. Easydriver är baserad på Allegro A3967-drivkrets Motorströmmen per lindning kan justeras från 150mA till 750mA Spänningsmatning för styrlogik är 5VDC Spänningsmatning på motorsidan är mellan 7-30VDC Varning: koppla inte i eller ur stegmotorn med spänning ansluten. Det kan skada drivkretsen permanent.
    Part.no: 41003089
    In stock: 20 
    Buy
    $18.69

  • L298 Dual H-Bridge Motor Driver

      L298 Dual H-Bridge Motor Driver
    Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals. The emitters of the lower transistors of each bridge are connected together and the corresponding external terminal can be used for the con-nection of an external sensing resistor. An additional supply input is provided so that the logic works at a lower voltage. - Light weight, small dimension - Super driver capacity - FWD protection - Heavy load Heat sink - 2 current probe port - Power selection switch - 4 pull up resistor switch - 2 DC motor/ 4 coil dual phrase stepper motor output - Motor direction indication LED - 4 standard mouting hole Spec: - Driver: L298 - Driver power supply: +5V~+46V - Driver Io: 2A - Logic power output Vss: +5~+7V (internal supply +5V) - Logic current: 0~36mA - Controlling level: Low -0.3V~1.5V, high: 2.3V~Vss - Enable signal level: Low -0.3V~1.5V, high: 2.3V~Vss - Max power: 25W (Temperature 75 cesus) - Working temperature: -25C~+130C - Dimension: 60mm*54mm - Driver weight: ~48g - Other extensions: current probe, controlling direction indicator, pull-up resistoer switch, logic part power supply.
    Part.no: 41010631
    Currently not in stock
    Buy
    $30.00

  • Motor Driver 1A Dual TB6612FNG

      Motor Driver 1A Dual TB6612FNG
    The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop. The two motor outputs (A and B) can be separately controlled, the speed of each motor is controlled via a PWM input signal with a frequency up to 100kHz. The STBY pin should be pulled high to take the motor out of standby mode. Logic supply voltage (VCC) can be in the range of 2.7-5.5VDC, while the motor supply (VM) is limited to a maximum voltage of 15VDC. The output current is rated up to 1.2A per channel (or up to 3.2A for a short, single pulse). Board comes with all components installed as shown. Decoupling capacitors are included on both supply lines. All pins of the TB6612FNG are broken out to two 0.1" pitch headers; the pins are arranged such that input pins are on one side and output pins are on the other. Features: Power supply voltage: VM=15V max, VCC=2.7-5.5V Output current: Iout=1.2A(average) / 3.2A (peak) Standby control to save power CW/CCW/short brake/stop motor control modes Built-in thermal shutdown circuit and low voltage detecting circuit All pins of the TB6612FNG broken out to 0.1" spaced pins Filtering capacitors on both supply lines Dimensions: 0.8x0.8"
    Part.no: 41011860
    In stock: 10 
    Buy
    $11.93

  • Motor driver 2 channels serial

      Motor driver 2 channels serial
    The Serial Controlled Motor Driver allows you to control up to two DC motors using a serial command interface. The serial interface is easy to use and it lets the user select an individual motor, the direction, and the desired speed constant (up to 10 different speed from stop to full speed). The board is based on the L298 Dual Full-Bridge Motor Driver from ST Micro. The motor driver can provide up to 4 Amps of current to the motors (2 Amps per motor). Power can be applied to either the two-pin JST connector or the GND and VCC header pins. Supplied power should be DC and within 5-16V. Please note, the pin labeled '5V' should only be used as an output. The serial command interface used to control the motors is very straightforward. A command consists of four characters: the motor number, the direction indicator, the speed constant, and a carriage return. The baud rate of the Serial Controlled Motor Driver is set to 115200bps (8-N-1). Features: * Serially control two motors separately * 115200bps (8-N-1) * Very straightforward command set * Drive up to 2A per motor (4A total) * Speed control * Forward/reverse control * Over-current detection * LEDs indicate over-current state * Unused ATmega328 pins broken out for custom use * Dimensions: 2.10 x 1.30 " (53.34 x 33.02 mm)
    Part.no: 41012711
    In stock: 6 
    Buy
    $38.43

  • Motor driver L298 2 channels 7-40V 2.5A

      Motor driver L298 2 channels 7-40V 2.5A
    BB-L298 is dual full bridge driver with up to 2.5A and 7-40V working voltage. It is good to drive Gear Robot motors with reversal function. STATUS LEDs visualize power supply and driver direction. The power connectors are spring type for quick connect disconnect. Inductive load protection diodes are included.   Up to 2.5A loads 7-40VDC power supply STATUS PWR LED STATUS direction LEDs for both channels Can work with 5V Arduino boards Suitable for the motors of OLIMEX robot wheels like MG gear motor Able to drive two motors
    Part.no: 41014058
    In stock: 4 
    Buy
    $15.54

  • Motordrivare VNH3SP30 1 kanal 5.5-36V 30A

      Motordrivare VNH3SP30 1 kanal 5.5-36V 30A
    VNH3SP30 is full bridge driver with up to 30A and 36V working voltage. It is good to drive Gear Robot motors with reversal function. STATUS LEDs visualize power supply and driver direction. The power connectors are spring type for quick connect disconnect. Inductive load protection diodes are included.   Up to 30A loads 5.5-36VDC power supply STATUS PWR LED STATUS direction LEDs Can work with 5V Arduino boards
    Part.no: 41014059
    Currently not in stock
    Buy
    $15.54

  • Quadstepper Motor Driver Board

      Quadstepper Motor Driver Board
    The Quadstepper motor driver board allows you to control up to 4 bipolar stepper motors simultaneously using logic level IO pins. Each motor driver has an output drive capacity of 35V and 2Amps. The board is capable of driving motors in full, half, quarter, eight, and sixteenth-step modes. The logic levels are selectable between 3.3V and 5V by way of a jumper. The bus header allows you to control all four motors with only 6 IO pins by controlling the enable (EN pins) for each motor, although each motor will be activated alone, not simultaneously. Be sure to close all of the 'Bus Enable' jumpers on the back of the board in order to use the Bus header. The Quadstepper is a great board for 3D printing applications as well as a host of other applications where it's necessary to control precise movement from logic level IO pins. Note: The board will only work with stepper motors similar to the one we sell. Higher power steppers will have problems with thermal control on the PCB. Features: * Can control up to 4 bipolar stepper motors simultaneously. * Each motor driver has an output drive capacity of 35V and 2Amps. * Capable of driving motors in full, half, quarter, eight, and sixteenth-step modes. * Power input (barrel jack) needs to be less than 30V and supply enough current for your specific stepper motors. * Jumper (labeled "5V") controls power to the motor drivers, logic levels, and VOUT pin, selectable 3.3/5V. * Bus header allows you to control all four motors with only 6 IO pins by controlling the enable (EN pins) for each motor
    Part.no: 41004687
    In stock: 3 
    Buy
    $81.19

  • serial multiplexer TS3A5017

      serial multiplexer TS3A5017
    This is a breakout board for the TS3A5017 Serial Multiplexer. The TS3A5017 is a dual single-pole quadruple-throw (4:1) analog switch that is designed to operate from 2.3 V to 3.6 V. This device can handle both digital and analog signals, and signals up to V+ can be transmitted in either direction. Features: * Isolation in the Powered-Down Mode, V+ = 0 * Low ON-State Resistance (10 Ohm) * Low Charge Injection * Excellent ON-State Resistance Matching * Low Total Harmonic Distortion (THD) * 2.3-V to 3.6-V Single-Supply Operation * Latch-Up Performance Exceeds 100 mA
    Part.no: 41004215
    In stock: 3 
    Buy
    $6.19

  • Servo Trigger

      Servo Trigger
    Servo Trigger is a small robotics board that simplifies the control of hobby RC servo motors. When an external switch or logic signal changes state, the Servo Trigger is able to tell an attached servo motor to move from position A to position B. To use the Servo Trigger, you simply connect a hobby servo and a switch, then use the on-board potentiometers to adjust the start/stop positions and the transition time. You can use a hobby servos in your projects without having to do any programming! The heart of the Servo Trigger is an Atmel ATTiny84 microcontroller, running a small program that implements the servo control features we are discussing here. On-board each Servo Trigger you will find three potentiometers, A sets the position the servo sits in while the switch is open, B sets the position the servo moves to when the switch is closed, and T sets the time it takes to get from A to B and back. Compared to a servo motor, the Servo Trigger board draws very little current, roughly 5 mA at 5V. Be sure to note that if youre using the Servo Trigger to control your motor, the absolute maximum supply voltage that should be applied is 5.5 VDC. Additionally, the SparkFun Servo Trigger is designed to make it easy to daisy chain boards you can simply connect the VCC and GND pads on adjacent boards to each other. Note: Check out the Hookup Guide in the Documents section below for more advanced tips, configurations, and modes! Features: Recommended Voltage: 5VDC Max Voltage: 5.5VDC Current Draw: 5 mA Three Control Settings A - sets the position the servo sits in while the switch is open B - sets the position the servo moves to when the switch is closed C - sets the time it takes to get from A to B and back Easy Control with Potentiometers Configurable Input Polarity Configurable Response Mode Compatible with Analog Servos ISP Header pins Available for Reprogram
    Part.no: 41013705
    In stock: 2 
    Buy
    $23.98

  • SparkFun Serial Controlled Motor Driver

      SparkFun Serial Controlled Motor Driver
    The SparkFun Serial Controlled Motor Driver (SCMD) is a DC motor driver thats been designed to drive small DC motors with ease. The SCMD is designed to emulate a typical register-based device in operation. It can be commanded by UART, I2C or SPI communication, and it can drive a constant 1.2A load per motor (peak 1.5A) at 11V. Need more than two motors? Chain multiple SCMDs together and command them through the same serial interface. Need more current? Each boards output can be bridged to allow double current. This driver board was designed to be affordable, compact and have more features than previous versions of serial-controlled motor drivers. Its main advantage is the variability of drive levels, making fine control adjustments a possibility. The SCMD is a 3.3V logic device! If you need to interface to 5V, youll need to use a logic level converter or modify the SCMDs from stock to operate at 5V and supply your own regulated 5V. Features: 1.5A peak drive per channel, 1.2A steady state Operates from 3 to 11 volts with 12V absolute max 3.3V default VCC and logic Max VCC in of 5.5V 127 levels of DC drive strength. Controllable by I2C, SPI or TTL UART signals Direction inversion on a per motor basis Global Drive enable Expansion port utilizing I2C, allows 16 additional drivers Exposed TO-220 heat sink shape Several I2C addresses, default UART bauds available Bridgeable outputs Optional fail-safe and diagnostics available. Configurable expansion bus bit rate to 50, 100 or 400kHz. Configurable expansion bus update rate from 1ms to 255ms, or by command only
    Part.no: 41015297
    In stock: 10 
    Buy
    $23.98

  • Stepper motor 28BYJ-48 with driver ULN2003A

      Stepper motor 28BYJ-48 with driver ULN2003A
    Stepper motor with ULN2003A based driver board. The board can be connected directly to a microcontroller and controls the motor by sending alternating pulses to the motor coils. The onboard LEDs indicate which coils/outputs are active. The motor has a gearbox with 64:1 ratio. * Supply voltage: 5 - 6VDC * Dimensions (driver): 29 x 21mm * Dimensions (motor): ø28x19mm * Poles: 4 (unipolar) * Gear ratio: 64:1 * Step angle: 5.625° (/64) * Steps per rev.: 4096 * DC resistance: 200ohm (±7%) * Shaft: 5mm flat
    Part.no: 41014801
    In stock: 54 
    Buy
    $17.95

  • Stepper motor driver A4983 2-ch

      Stepper motor driver A4983 2-ch
    A4983 driver can control stepper motors and have two channels. The board can also power gear motors. It might be supplied by voltage in the 6V to 35V range. Arduino, Pinguino, Maple can be used to control motors via this board. The spring contacts allow easy connect-disconnect of motor cables and power supplies. Jumper wires can be used to connect to Arduino/Maple/Pinguino/Duinomite-compatible boards. Up to 2.5A loads 6-35VDC power supply STATUS PWR LED Works from -20 to +85 degrees Celsius Suitable for the motors of OLIMEX wheels like MG gear motor
    Part.no: 41013356
    In stock: 14 
    Buy
    $14.34

  • Stepper motor module

      Stepper motor module
    Modul with driver and steppermotor
    Part.no: 41010554
    In stock: 4 
    Buy
    $19.16

  • USB servo controller 6ch

      USB servo controller 6ch
    The Micro Maestro is the first of Pololus second-generation USB servo controllers. The board supports three control methods (USB for direct connection to a PC, TTL serial for use with embedded systems, and internal scripting for self-contained, host controller-free applications) and channels that can be configured as servo outputs for use with radio control (RC) servos or electronic speed controls (ESCs), digital outputs, or analog inputs. The Micro Maestro is a highly versatile six-channel servo controller and general I/O board in a highly compact (0.85 x 1.20") package. The extremely accurate, high-resolution servo pulses have a jitter of less than 200 ns, making this servo controller well suited for high-precision animatronics, and built-in speed and acceleration control make it easy to achieve smooth, seamless movements without requiring the control source to constantly compute and stream intermediate position updates to the Micro Maestro. This kit includes the headers as shown in the first picture, the headers do not come populated. Features: Three control methods: USB, TTL (5V) serial, and internal scripting 0.25µs output pulse width resolution (corresponds to approximately 0.025° for a typical servo, which is beyond what the servo could resolve) Pulse rate configurable from 33 to 100 Hz Wide pulse range of 64 to 3280 µs when using all six servos with a pulse rate of 50 Hz Individual speed and acceleration control for each channel Channels can also be used as general-purpose digital outputs or analog inputs A simple scripting language lets you program the controller to perform complex actions even after its USB and serial connections are removed Free configuration and control application for Windows makes it easy to: Configure and test your controller Create, run, and save sequences of servo movements for animatronics and walking robots Write, step through, and run scripts stored in the servo controller Virtual COM port makes it easy to create custom applications to send serial commands via USB to the controller TTL serial features: Supports 300 - 250000 kbps in fixed-baud mode Supports 300 - 115200 kbps in autodetect-baud mode Simultaneously supports the Pololu protocol, which gives access to advanced functionality, and the simpler Scott Edwards MiniSSC II protocol (there is no need to configure the device for a particular protocol mode) Can be daisy-chained with other Pololu servo and motor controllers using a single serial transmit line Board can be powered off of USB or a 5 - 16 V battery, and it makes the regulated 5V available to the user Compact size of 0.85" × 1.20" (2.16 × 3.05 cm) and light weight of 0.17 oz (4.8 g) Upgradable firmware
    Part.no: 41004688
    In stock: 3 
    Buy
    $24.94