Light effects

Showing 1 to 35 of 35 matching products
Sort by
 
  • DC-motorstyrning / LED-dimmer

      DC-motorstyrning / LED-dimmer
    Module for speed control of DC-motors or for dimming LEDs. Works by pulse-width modulation (PWM). Built around a 555-timer IC. Max load: 6-15 V / 500mA Also available as DIY-kit, art-no; 12100804
    Part.no: 21200804
    In stock: 14 
    Buy
    $16.75

  • DELight Starter Kit

      DELight Starter Kit
    The DELight Starter Kit combines all the components of the DELight programmable lighting system into one package. It consists of a programmable lighting controller, software for creating customized lighting sequences, a USB link cable to load the programs and ultra-bright LED lights. Everything you need to create scale, sport or nightflying effects for R/C airplanes, cars, robots or special effects is included. The DELink software is easy to use and completely graphical. A simulator allows you to preview and fine-tune your programs. Infinite undo (even inside saved files) means you'll never have an 'oops' moment. The software is a free download, so you are welcome to download it before purchasing the system in order to verify that you can achieve the effects you want. The DELight Ultra Bright LED's are the brightest LED's ever used in an R/C lighting system. They are up to 15 lumens each and can each draw up to 150mA. Not to worry, the DELight controller can handle this level of power, and if you're worried about blinding yourself, the controller has programmable brightness! The DELight Controller has eight output channels. It contains onboard non-volatile memory to store your programs, and the power electronics required to sequence and dim the LED's according to your command. It is connected to your receiver through any spare channel (or use a Y harness.) The point at which the sequences turn on or change is programmable, so effects such as landing lights are easily accomplished. Two of the programmable channels are even higher powered - up to two amps on/off, and can be used to power things such as glow-wire inverters or bomb drops, in addition to powering LEDs. Model: DELight Starter Kit Contains: DELink DELight Controller USB Cable 2 - Ultra Bright White LEDs w/ 24" Pigtails 1 - Ultra Bright Red LED w/ 24" Pigtails 1 - Ultra Bright Green LED w/ 24" Pigtails Flying Weight: 11.6g/.41oz Applications: Scale Lighting Night Flying Sport light for airplanes R/C car lighting effects such as underbody glow, turn signals or headlights Theatrical and special effects Programmability: 106 brightness/sequence blocks, programmable input control, hysteresis and turn-on point
    Part.no: 41010063
    In stock: 2 
    Buy
    $60.12

  • DELink USB link

      DELink USB link
    The DELink USB Link is the perfect compliment to our DELight Controller. Coupled with the DELink Software, you can design, test, and preview your lighting sequences with ease. Utilizing the easy-to-use USB bus, programming your DELight Controller is one click away! 1m USB cable included.
    Part.no: 41010061
    In stock: 9 
    Buy
    $28.80

  • DMX controller for LED-strips 4 channels

      DMX controller for LED-strips 4 channels
    Four channel DMX controller for LED-strips. Can be used to control four separate strips with one color or one strip with four colors (red, green, blue and white). Can deliver up to 4A per channel. Specifications: DMX channels: 4 Supply voltage: 12-24VDC Power output: 12 V: Output current: 4x 4A Input signal: DMX512 (XLR and RJ45) Greyscale levels: 256 (8 bits) PWM frequency: ± 2600 Hz Weight: 310g Dimensions: 165 x 68 x 40mm
    Part.no: 41012668
    In stock: 1 
    Buy
    $60.12

  • FemtoBuck LED-drivare 1-kanal 350mA

      FemtoBuck LED-drivare 1-kanal 350mA
    This is the FemtoBuck, a small-size single-output constant current LED driver. Each FemtoBuck has the capability to dim a single high-power channel of LEDs from 0-350mA at up to 36V while the dimming control can be either accessed via PWM or analog signal from 0-2.5V. This board is based off of the PicoBuck LED Driver, developed in collaboration with Ethan Zonca, except instead of blending three different LEDs on three different channels the FemtoBuck controls just one. For the FemtoBuck, weve increased the voltage ratings on the parts to allow the input voltage to cover the full 36V range of the AL8805 driver. Since the FemtoBuck is a constant current driver, the current drawn from the supply will drop as supply voltage rises. In general, efficiency of the FemtoBuck is around 95%, depending on the input voltage. On board each FemtoBuck you will find two inputs for both power input and dimming control pins and an area to install a 3.5mm screw terminal. Finally at either side of the board you will find small indents or ears which will allow you to use a zip tie to secure the wires to the board after soldering them down.
    Part.no: 41014052
    In stock: 5 
    Buy
    $11.93

  • LED dimmer RGB w. remote control

      LED dimmer RGB w. remote control
    Features * easy remote control operation * Hi power MOSFET outputs * ideal for use with common anode led strips * 8 Transmitters auto-learning function * 7 colour tones * 10 dimming steps * transmitter included * optional: o 2-CHANNEL RF REMOTE CONTROL: VM130T o USB TO RF REMOTE CONTROL TRANSMITTER: K8074 * recommended power supply: PSIN04012 Specifications * LED PWM frequency: ± 300Hz * 3x 12V/3A outputs * TX/RX: 433MHz operation * power supply: max. 12V/9A * dimensions: ± 80x70x23mm/3.15x2.75x0.9" 1 remote control "VM130T" included.
    Part.no: 12000162
    In stock: 2 
    Buy
    $67.35

  • LED flasher energy saving

      LED flasher energy saving
    This circuit is energy saving LED flasher. There is the light checking sensor. When the area is getting dark, LED will flashing periodically, that's make this circuit live longer. It is suitable to use as a nevigator lamp on-off switch in the dark, or to be a caution lamp circuit for bicycle. Technical Specifications: - Power supply : 3VDC. (CR2032 battery not included) - Duration of battery : 1}200 hour. - Frequency of flashing : 0.5 second. - PCB dimensions : 1.42 x 1.49 in.
    Part.no: 21200183
    In stock: 22 
    Buy
    $7.11

  • LED module color changing

      LED module color changing
    Module with a color-changing LED. As long as the input pin is high, the LED will cycle automatically and randomly through different colors.
    Part.no: 41015722
    In stock: 99 
    Buy
    $3.49

  • LED module Red/Green 3mm

      LED module Red/Green 3mm
    Module with a red/green LED. The LED is connected with a common cathode. As each color can be controlled individually, the LED can be made to light up in red, gren or any mix of both. Please observe that the LED requires one resistor per color to limit the current! Suitable resistors for 5V operation: Red: 180ohm Green: 100ohm
    Part.no: 41015718
    In stock: 99 
    Buy
    $3.49

  • LED module Red/Green 5mm

      LED module Red/Green 5mm
    Module with a red/green LED. The LED is connected with a common cathode. As each color can be controlled individually, the LED can be made to light up in red, gren or any mix of both. Please observe that the LED requires one resistor per color to limit the current! Suitable resistors for 5V operation: Red: 180ohm Green: 100ohm
    Part.no: 41015717
    In stock: 99 
    Buy
    $3.49

  • LED module RGB

      LED module RGB
    Module with an RGB LED. The LED is connected with a common anode and current limiting resistors for each color. As each color can be individually controlled with PWM, practically any color can be generated!
    Part.no: 41015715
    In stock: 99 
    Buy
    $3.49

  • LED module RGB SMD

      LED module RGB SMD
    Module with an surface mounted RGB LED. The LED is connected with a common cathode. As each color can be individually controlled with PWM, practically any color can be generated. Please observe that the LED requires one resistor per color to limit the current! Suitable resistors for 5V operation: Red: 180ohm Green: 100ohm Blue: 100ohm
    Part.no: 41015716
    In stock: 99 
    Buy
    $3.49

  • LED RGB dimmer w. RF remote controller

      LED RGB dimmer w. RF remote controller
    Features * easy remote control operation * Hi power MOSFET outputs * ideal for use with common anode led strips * 8 Transmitters auto-learning function * 7 colour tones * 10 dimming steps * transmitter included * optional: o 2-CHANNEL RF REMOTE CONTROL: VM130T o USB TO RF REMOTE CONTROL TRANSMITTER: K8074 Specifications * LED PWM frequency: ± 300Hz * 3x 12V/3A outputs * TX/RX: 433MHz operation * power supply: max. 12V/9A * dimensions: ± 80x70x23mm/3.15x2.75x0.9"
    Part.no: 12009162
    In stock: 2 
    Buy
    $60.12

  • LED RGB kaskadkopplingsbar

      LED RGB kaskadkopplingsbar
    Nice little RGB LED-module that can be cascaded into long chains. The module is based on P9813 LED-driver and communicates via a serial interface (DATA, CLK). Read more about this product on the wiki-page, found under the tab files. Operating voltage: 5V Operating current: 20mA
    Part.no: 41011147
    In stock: 26 
    Buy
    $15.54

  • LED strip driver

      LED strip driver
    The LED Strip Driver with 4-pin Grove interface provides easy connectivity to your standard Arduino device or Seeed Stalker. It can help you control the luminance of a single-color LED strip, as well as the color and the luminance of an RGB LED strip through Arduino. It has 2 terminals and 2 Grove interfaces. The power for the LED strip comes in through the 2-pin terminal. And the LED controlling voltages output through the 4-pin terminal. The 2 Grove interfaces are respectively screen-printed IN (for controlling data input) and OUT (for controlling data shared with the next strip driver). It can drive an LED strip 1 to 2 meters long with 9 V, while 1 to 5 meters long with 12 V. The driver in conjunction with the colorful LED strips can add a wonderful effect to indoor or outdoor usages. Features Grove compatible interface Can be cascaded for a larger display Best results achieved with LED strips 5 meters long or shorter Outputs PWM signals 256 gray-levels are adjustable via programming Arduino and MEGA compatible Screw Terminals (power input and control signal output interface)
    Part.no: 41011146
    In stock: 4 
    Buy
    $15.54

  • Light effect geberator 10ch 12VDC

      Light effect geberator 10ch 12VDC
    10 x 12V/400mA outputs to control cold-cathode fluorescent lamps (using FLPS adapter), light bulbs, LEDs and "solid state" relays, ... for use with advertisement lighting, party lights, eye-catchers, in the disco... ten pre-programmed light patterns selectable with a push button the number of used channels is adjustable the last used lighting effect is saved in non-volatile memory adjustable speed LED indication for every output 12V operation possible for use in cars options: adapter: PSS1255 (12V output 5.5A) power supply for cold-cathode fluorescent lamps: FLPS (300mm) or FLPS1 (100mm) cold-cathode fluorescent lamps: FL(xx) - (100 or 300mm) solid-state relays: VR25SS1A or VR3SS1A to drive mains voltage lamps also available in kit version: K8044 Specifications power supply: 12V DC outputs: 12V DC / 400mA per channel (total : max 4A) dimensions PCB: 140 x 100 x 27mm (5.5" x 3.9" x 1.1")
    Part.no: 12009120
    In stock: 2 
    Buy
    $60.12

  • NeoPixel matrix 8x8 RGB LEDs 71x71mm

      NeoPixel matrix 8x8 RGB LEDs 71x71mm
    8x8 matrix of 5x5mm NeoPixel RGB LEDs. Each LED is individually addressable and can be controlled with just one pin from a microkontroller. The panels can be chained to create larger units. Each LED has an integrated constant current driver, which makes the intensity of each LED consistent. As each LED can draw as much as 60mA at maximum intensity, a power supply that can provide atleast 2A at 5V is recommended. No external resistors are needed, just supply the board with ~5VDC and connect the data line to a micro controller! * Current consumption (each LED): max. 60mA (max. 3.8A in total, typical 1-2A) * Supply voltage: 4 - 7VDC * Dimensions: 71.17 x 71.17 x 3.28mm (2.8 x 2.8 x 0.12") * Weight: 24.21g * LEDs: WS2812
    Part.no: 41012476
    In stock: 7 
    Buy
    $48.07

  • NeoPixel ring 16 RGB LEDs ø44.5mm

      NeoPixel ring 16 RGB LEDs ø44.5mm
    LED ring with 16pcs 5x5mm NeoPixel RGB LEDs. Each LED is individually addressable and can be controlled with just one pin from a microkontroller. Multiple rings can be chained to create larger units. Each LED has an integrated constant current driver, which makes the intensity of each LED consistent. No external resistors are needed, just supply the board with ~5VDC and connect the data line to a micro controller! * Current consumption (each LED): ~18mA (~288mA in total) * Supply voltage: 4 - 7VDC * Dimensions: outer diameter - 44.5mm, inner diameter - 31.75mm, thickness - 2.54mm (1.75 x 1.25 x 0.1") * Weight: 3.03g * LEDs: WS2812
    Part.no: 41012478
    In stock: 1 
    Buy
    $15.54

  • NeoPixel ring 24 RGB LEDs ø66mm

      NeoPixel ring 24 RGB LEDs ø66mm
    LED ring with 24pcs 5x5mm NeoPixel RGB LEDs. Each LED is individually addressable and can be controlled with just one pin from a microkontroller. Multiple rings can be chained to create larger units. Each LED has an integrated constant current driver, which makes the intensity of each LED consistent. No external resistors are needed, just supply the board with ~5VDC and connect the data line to a micro controller! * Current consumption (each LED): ~18mA (~432mA in total) * Supply voltage: 4 - 7VDC * Dimensions: outer diameter - 66mm, inner diameter - 52.5mm, thickness - 3.5mm (2.6 x 2.05 x 0.125") * Weight: 6.23g * LEDs: WS2812
    Part.no: 41012477
    In stock: 11 
    Buy
    $30.00

  • NeoPixel stick 8 RGB LEDs 51mm

      NeoPixel stick 8 RGB LEDs 51mm
    LED stick with 8pcs 5x5mm NeoPixel RGB LEDs. Each LED is individually addressable and can be controlled with just one pin from a microkontroller. Multiple sticks can be chained to create larger units. Each LED has an integrated constant current driver, which makes the intensity of each LED consistent. No external resistors are needed, just supply the board with ~5VDC and connect the data line to a micro controller! * Current consumption (each LED): ~18mA (~144mA in total) * Supply voltage: 4 - 7VDC * Dimensions: 51.10 x 10.22 x 3.19 (2 x 0.4 x 0.12") * Weight: 2.57g * LEDs: WS2812
    Part.no: 41012479
    Currently not in stock
    Buy
    $8.31

  • PicoBuck LED-drivare 3-kanaler 350mA

      PicoBuck LED-drivare 3-kanaler 350mA
    The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. Power is supplied to the PicoBuck through a wide range of input voltages (6v to 20v) connected to the VIN header and three inputs for each driver channel (labeled IN1, IN2, and IN3) driven with standard 3.3v or 5v logic. This PicoBuck supports PWM control so long as the signal is above a minimum of ~1.5V and each LED is driven to ~350mA.
    Part.no: 41014051
    In stock: 10 
    Buy
    $20.36

  • PWM LED dimmer 12-bit 12-ch SPI

      PWM LED dimmer 12-bit 12-ch SPI
    For all of you out there who want to control 12 channels of PWM, we salute you! We also would like you to check out this breakout board for the TLC59711 PWM driver chip. This chip can control 12 separate channels of 16-bit PWM output. This is the highest-resolution PWM board we've seen! Designed (and ideal) for precision LED control. Only two "SPI" pins are required to send data (our Arduino library shows how to to use any digital microcontroller pins). Best of all, the design is completely chainable. As long as there's enough power for all the boards you can chain as many as you'd like, like a little trail of blue PCBs stretching out into the sunset. Each of the 12 outputs are constant-current and open drain. You can drive multiple LEDs in series, with a V+ anode supply of up to 17V. If you want to drive something that requires a digital input, you must use a pullup resistor from the drive pin to your logic level to create the full waveform. One resistor is used to set the current for each of the outputs, the constant current means that the LED brightness doesn't vary if the power supply dips. We use a 3.3K resistor for about 15mA but you can solder a thru-hole resistor over it if you'd like to change that value. Check the TLC59711 datasheet for details on resistor-to-current values. There's also a handy on-chip 3.3V regulator which you can use if you need a logic level regulator. We include a few extras to make this board easy to use: a green power-good LED, four mounting holes and a current-set resistor. A bit of 0.1" header is also included so you can solder it on and plug into a breadboard. To use: Power V+ with 5-17VDC, and connect ground to the common ground. Then send 3-5V logic SPI data on DIN (data in) and CLK (clock). Notes: 1. This board is not good for driving servos. 2. There's a typo in the silkscreen, the second R0 should be R1
    Part.no: 41011834
    In stock: 4 
    Buy
    $11.93

  • PWM LED dimmer 12-bit 24-ch SPI

      PWM LED dimmer 12-bit 24-ch SPI
    For all of you out there who want to control 24 channels of PWM, we salute you! We also would like you to check out this breakout board for the TLC5947 PWM driver chip. This chip can control 24 separate channels of 12-bit PWM output. Designed (and ideal) for LED control, this board is not good for driving servos. If you need to drive servos, we have a controller for that over here. Only three "SPI" pins are required to send data (our Arduino library shows how to to use any digital microcontroller pins). Best of all, the design is completely chainable. As long as there's enough power for all the boards you can chain as many as you'd like, like a little trail of blue PCBs stretching out into the sunset. Each of the 24 output's is constant-current and open drain. You can drive multiple LEDs in series, with a V+ anode supply of up to 30V. If you want to drive something that requires a digital input, you must use a pullup resistor from the drive pin to your logic level to create the full waveform. One resistor is used to set the current for each of the outputs, the constant current means that the LED brightness doesn't vary if the power supply dips. We use a 3.3K resistor for about 15mA but you can solder a thru-hole resistor over it if you'd like to change that value. Check the TLC5947 datasheet for details on resistor-to-current values. We include a few extras to make this board easy to use: a durable 5V low-dropout regulator (with reverse polarity protection in case y'know, you plug it in backwards), a green power-good LED, four mounting holes and a current-set resistor. A bit of 0.1" header is also included so you can solder it on and plug into a breadboard. To use: Power V+ with 5-30VDC, and connect ground to the common ground. Then send 3-5V logic SPI data on DIN (data in), CLK (clock) and LAT (latch). If you'd like to quickly turn off all the outputs, raise the OE pin - it's pulled low to enable the PWM outputs.Our Arduino library will get you started with blinking LEDs, install it and run the example code with the noted pin configuration.
    Part.no: 41013172
    In stock: 8 
    Buy
    $20.36

  • PWM LED dimmer 16-bit 12-ch SPI

      PWM LED dimmer 16-bit 12-ch SPI
    For all of you out there who want to control 12 channels of PWM, we salute you! We also would like you to check out this breakout board for the TLC59711 PWM driver chip. This chip can control 12 separate channels of 16-bit PWM output. This is the highest-resolution PWM board we've seen! Designed (and ideal) for precision LED control, this board is not good for driving servos. If you need to drive servos, we have a controller for that over here. Only two "SPI" pins are required to send data (our Arduino library shows how to to use any digital microcontroller pins). Best of all, the design is completely chainable. As long as there's enough power for all the boards you can chain as many as you'd like, like a little trail of blue PCBs stretching out into the sunset. Each of the 12 outputs are constant-current and open drain. You can drive multiple LEDs in series, with a V+ anode supply of up to 17V. If you want to drive something that requires a digital input, you must use a pullup resistor from the drive pin to your logic level to create the full waveform. One resistor is used to set the current for each of the outputs, the constant current means that the LED brightness doesn't vary if the power supply dips. We use a 3.3K resistor for about 15mA but you can solder a thru-hole resistor over it if you'd like to change that value. Check the TLC59711 datasheet for details on resistor-to-current values. There's also a handy on-chip 3.3V regulator which you can use if you need a logic level regulator. We include a few extras to make this board easy to use: a green power-good LED, four mounting holes and a current-set resistor. A bit of 0.1" header is also included so you can solder it on and plug into a breadboard. To use: Power V+ with 5-17VDC, and connect ground to the common ground. Then send 3-5V logic SPI data on DIN (data in) and CLK (clock). Our Arduino library will get you started with blinking LEDs, install it and run the example code with the noted pin configuration. There's a typo in the silkscreen, the second R0 should be R1 - but you knew that already!
    Part.no: 41013178
    In stock: 7 
    Buy
    $11.93

  • RGB controller w. remote controller

      RGB controller w. remote controller
    Features suited for both incandescent bulbs and LEDs hard transition effects: runnning light, Strobo, Colour loops, etc... smooth fade effects: colour change, flame effect, random colours, slow off etc... wide-range effect speed adjust memory for last selected effect & speed 5 user-editable colour tables Hi power MOSFET outputs addressable, control up to 7 units independently optional: 2-CHANNEL RF REMOTE CONTROL Specifications 256 intensity levels/ch. outputs: 12V/3A LED PWM freq: + 300Hz power supply: 12V/9A max TX/RX: 433MHz operation dimensions: + 80x70x23mm / 3.15 x 2.75 x 0.9"
    Part.no: 12000151
    In stock: 3 
    Buy
    $60.12

  • RGB LED controller

      RGB LED controller
    En controller som kan användas både till glödlampor och LED. Varje utgång kan justera upp/ner och ett antal ljuseffekter kan väljas, såsom rinnande ljus, stroboskop, färgslingor, färgbyte, lågor, slumpvis färger m.fl. Hastigheten är justerbar över ett brett område. Utgångarna är försedda med MOSFET och det finns minne som kommer ihåg de senaste inställningarna. Lämplig för LED-strips med gemensam anod. Levereras med inbyggnadslåda. Specifikationer: * 256 nivåer per kanal * utspänning samma som matningsspänning * möjlighet till strömbegränsning (kräver motstånd) * PWM-frekvens: 82 Hz * Matningsspänning: 10-15VDC, max 9A * Dimensioner: 80x70x23mm Levereras färdigbyggd. Finns även som byggsats (12008088)
    Part.no: 12000107
    In stock: 2 
    Buy
    $46.63

  • RGB LED dimmer for DIN-rail

      RGB LED dimmer for DIN-rail
    For use with: - 12-24VDC common anode RGB or single colour led strips - 12-24VDC led armatures Features easy DIN-rail mounting Hi-power outputs Dual pushbutton operation Press to select colour Press to adjust intensity Buttons can be paralleled Single colour mode Short circuit protection Specifications PWM freq.: 90Hz power supply: 12-24VDC (e.g. Velleman LPS series) Max output current: 5A /channel DIN-rail enclosure: 2 modules wide
    Part.no: 12008150
    In stock: 4 
    Buy
    $63.73

  • RGB slavemodule 3x4A

      RGB slavemodule 3x4A
    Multiply the output power of your Velleman LED controller ! Features add more led strips to your existing controller every unit adds up to 144W (12V) or 288W (24V) works with a single power supply or multiple supplies eases distribution of led strips allows simultaneous use of 12V and 24V strips only 4 interconnecting wires required Specifications open collector/drain inputs power supply: 12-24VDC / 12A max. dimensions: 80 x 70 x 23mm / 3.14 x 2.75 x 0.9"
    Part.no: 12008169
    In stock: 3 
    Buy
    $51.69

  • Running light

      Running light
    Rinnande ljus med 4 utgångar. Totalt 32 program, varav 10 som du själv kan programmera. Triac-utgångar för max 4A/220V (1000 W).
    Part.no: 12108055
    In stock: 6 
    Buy
    $23.98

  • Satellite Module 001 10xLED

      Satellite Module 001 10xLED
    The Satellite Module 001 is a 10 LED array of five-chip 100mA wide-angle (140 degree) red, green, and blue LEDs. The perceived output power of the red channel is a little less than the blue and green channels, so there are 4 red, 3 blue, and 3 green LEDs. Each LED supplies ~35,000 mcd over a 140 degree viewing angle. Combine with the ShiftBar to create a string of super-bright clusters. These are as bright as 15 ShiftBrites on the blue and green, and 20 ShiftBrites on the red channel!
    Part.no: 41004523
    In stock: 9 
    Buy
    $21.19

  • ShiftBar Led controller

      ShiftBar Led controller
    The ShiftBar is a medium-power RGB LED controller, capable of powering three channels of LEDs from 10mA to 150mA and from 5V to 17V. It's ideal for many common-anode RGB LED bars, such as the Satellite Module 001. It uses the same A6281 controller as the ShiftBrite, with daisy-chainable SPI communication that is simple to use with any microcontroller. Each channel is controlled with its own 10-bit PWM register and 7-bit current control register. A trim potentiometer allows the user to adjust overall current limiting to any desired maximum. The ShiftBar includes six screw terminal headers for wiring your own LEDs, as well as independent power. It also has two 6-pin headers that bring power and communications into and out of the device. Chains longer than four ShiftBars at maximum current should have power attached periodically, to counteract voltage drop along the power wires of a long chain.
    Part.no: 41004522
    In stock: 9 
    Buy
    $11.19

  • Sinewinder R/C lighting system

      Sinewinder R/C lighting system
    Sinewinder is an attractive, easy to use lighting system for your R/C vehicle. Just plug the Sinewinder light into a spare receiver channel, or use a separate 5V source. Sinewinder has 12 bright LEDs that scan from side to side, with a short trail after the leading light. The lights can be switched on and off by using your radio. If no signal is present or the signal wire is cut, the lights will default to being on. Specifications: Input voltage: 3V to 6V Current draw: 30mA max 4" / 10cm long Applications: Lighting on R/C planes, robots, cars, boats Automotive lighting PC case lighting Crimefighting in the 80s
    Part.no: 41010062
    In stock: 7 
    Buy
    $15.54

  • USB - DMX interface

      USB - DMX interface
    Velleman VM116, Features this unit can control DMX fixtures using a PC and USB interface test software and "DMX Light Player" software is included, a DLL is provided to write your own software furthermore there is a stand-alone test function that outputs all 512 channels at a time, with adjustable levels kit includes: nice enclosure USB cable CD with: test software, DLL for own developments, free DMX light player Specifications connected and powered through USB 512 DMX channels with 256 levels each 3 pin XLR-DMX output connector Windows 98SE or higher compatible DLL included to write your own software optional 9V battery needed for stand alone test mode solid state - fuse protection on DMX output dimensions: 106 x 101 x 44.5mm (4.2" x 4.0" x 1.8")
    Part.no: 12009116
    In stock: 1 
    Buy
    $126.39

  • WS2801 Breakout med RGB LED

      WS2801 Breakout med RGB LED
    Breakout för WS2801 med RGB LED Kan kopplas i en kedja där varje WS2801 är individuellt adresserbar.
    Part.no: 41000504
    In stock: 1 
    Buy
    $6.19

  • WS2812B Breakout med RGB LED

      WS2812B Breakout med RGB LED
    Breakout board with a single WS2812B RGB-LED. WS2812 is an RGB-LED with a built-in microcontroller that can be controlled via a 1-wire interface. Each LED has a data-input and a data-output that can be chained for an almost unlimited number of LEDs in series. The LED is powered with 5-7VDC and draws about 60mA at full brightness each.
    Part.no: 41015226
    In stock: 7 
    Buy
    $6.19