GPS modules

Showing 1 to 13 of 13 matching products
Sort by
 
  • Connector board for GPS modules

      Connector board for GPS modules
    Board that breaks out the connections from GPS modules to holes with 2.54mm pitch. The connector is a 1mm JST-header and is used by a number of GPS modules, such as GP-735, EM-406, EM-506 and more.
    Part.no: 41015016
    Expected:
    2017-08-29
    Buy
    $5.42

  • Connetion cable for EM401 o EM406 30cm

      Connetion cable for EM401 o EM406 30cm
    This is an extra long communication cable, 1 foot in length, that mates with the EM406 and EM401. Cut and hack this cable to your needs. Ideal if you have a UAV project where the GPS module may be a distance away from the controller board. Cable has two a 6-pin JST connectors with 1mm pitch. Wired pin 1 to pin 1.
    Part.no: 41004211
    In stock: 1 
    Buy
    $3.69

  • GP-735 GPS receiver 56ch TTL

      GP-735 GPS receiver 56ch TTL
    The GP-735 is a slim, ultra-high performance, easy to use GPS smart antenna receiver. With -162dBm tracking sensitivity and only 29 second cold start time, the GP735 is a tiny, yet powerful, piece of tech. The slim design makes it ideal for applications where you dont have a lot of space to work in. Really its quite small. This 56-channel GPS module, based on the uBlox 7th generation chipset, has an operating voltage of 3.3~5.5V, an antenna on board, and connects to your system via TTL serial. The 1Hz update rate is fast enough for the majority of applications (and can be increased to 10Hz if you need) so whether youre tracking a pet or building an autonomous car, the GP-735 has you covered! Note: We are carrying the T option of this module which is TTL-UART and not USB. Dimensions: 35 x 8 x 6.5 mm
    Part.no: 41014834
    Expected:
    2017-08-29
    Buy
    $60.12

  • GPS Evaluation Board

      GPS Evaluation Board
    This is an evaluation board for our various GPS modules that incorporates many new features! This one board supports connection to the various GPS modules sold by SparkFun. Serial interface for USB over the FT232RL and a classic RS232 interface. Power is provided over USB or a DC barrel jack. A power switch, port selection, and serial isolation switches are available. Supported Modules: FV-M8 (formerly EB-85A) EM406 EM408 Lassen iQ Copernicus (requires female socket installation) Features: On board 5V regulation Power over USB Power over 5.5x2.1mm barrel jack (center positive) Status LED 12mm Coin Cell backup battery holder Serial over USB (FT232RL VCP) Serial over dual RS232 connection All serial ports broken out Note: If using the Lassen iQ module, a piece of tape is needed to cover the exposed header under the module.
    Part.no: 41009993
    In stock: 2 
    Buy
    $49.94

  • GPS Receiver 14 Channel 20Hz - Venus638FLPx-L

      GPS Receiver 14 Channel 20Hz  - Venus638FLPx-L
    Venus638FLPx is a high performance, low cost, single chip GPS receiver targeting mobile consumer and cellular handset applications. It offers very low power consumption, high sensitivity, and best in class signal acquisition and time-to-first-fix performance. Venus638FLPx contains all the necessary components of a complete GPS receiver, includes 1.2dB cascaded system NF RF front-end, GPS baseband signal processor, 0.5ppm TCXO, 32.768kHz RTC crystal, RTC LDO regulator, and passive components. It requires very low external component count and takes up only 100mm2 PCB footprint. Note: According to the manufacturer's specifications, the IC requires a 24 hour pre-bake at 125C before SMD mounting in order to prevent issues with moisture . Features: -148dBm cold start sensitivity -165dBm tracking sensitivity 29 second cold start TTFF 3.5 second TTFF with AGPS 1 second hot start 2.5m accuracy Multipath detection and suppression Jamming detection and mitigation SBAS (WAAS / EGNOS) support 67mW full power navigation Works directly with active or passive antenna Internal flash for optional 75K point data logging Supports external SPI flash memory data logging Complete receiver in 10mm x 10mm x 1.3mm size Contains LNA, SAW Filter, TCXO, RTC Xtal, LDO Dimensions: 10 x 10 x 1.3mm, LGA69 package OBS! Detta är endast själva kretsen, kräver specialutrustning för montering då det är LGA69-kapsel
    Part.no: 41011710
    In stock: 2 
    Buy
    $50.48

  • GPS receiver EM-506 48 channels

      GPS receiver EM-506 48 channels
    The EM-506 GPS receiver from USGlobalSat based on the spectacular SiRF StarIII chipset. This complete module is built upon the same technology as the ET-301, but includes on-board voltage regulation, LED status indicator, battery backed RAM, and a built-in patch antenna! 6-pin interface cable included. This EM-506 GPS module is powered by SiRF Star IV, it can provide you with superior sensitivity and performance even in urban canyon and dense foliage environment. With SiRF CGEE (Client Generated Extended Ephemeris) technology, it predicts satellite positions for up to 3 days and delivers CGEE-start time of less than 15 seconds under most conditions, without any network assistance. Features: * 48-Channel Receiver * Extremely high sensitivity : -163dBm * 2.5m Positional Accuracy * Hot Start : 1s ' Warm Start : 35s / 15s with CGEE * Cold Start : 35s / 15s with CGEE * 45-55mA at 4.5-6.5V Dimensions: 30mm x 30mm x 10.7mm 16g including cable
    Part.no: 41012712
    Expected:
    2017-08-29
    Buy
    $50.48

  • GPS-antenna bolt assy

      GPS-antenna bolt assy
    Active aerial with bolt mount (M10) for GPS receivers. Powered by the GPS receiver via the aerial cable. Frequency: 1575 Mhz Antenna connection: SMA/M Cable length: 5 m Amplification: 5 dBi + 28 dB Mounting: Stud
    Part.no: 41004368
    Currently not in stock
    Buy
    $32.68

  • GPS-antenna magnetic 3V MCX

      GPS-antenna magnetic 3V MCX
    Magnet mount antenna for GPS modules operating at 3V. Designed for automobile use. Gain 26dB VSWR Cable: 5 m with MCX-connector Voltage 3.3V +/- 0.5V Current 12mA Weight 50g
    Part.no: 41003274
    In stock: 1 
    Buy
    $16.19

  • GPS-antenna magnetic 3V SMA

      GPS-antenna magnetic 3V SMA
    Magnet mount antenna for GPS modules operating at 3V. Designed for automobile use. Gain 26dB VSWR Cable: 5 m with SMA-connector Voltage 3.3V +/- 0.5V Current 12mA Weight 50g
    Part.no: 41003275
    In stock: 3 
    Buy
    $16.75

  • GPS-mottagare 66 kanaler LS20031 5Hz med smart antenn

      GPS-mottagare 66 kanaler LS20031 5Hz med smart antenn
    The LS20031 GPS receiver is a complete 5Hz GPS smart antenna receiver, that includes an embedded antenna and GPS receiver circuits. This low-cost unit outputs an astounding amount of position information 5 times a second. The receiver is based on the proven technology found in LOCOSYS 66 channel GPS SMD type receivers that use MediaTek chip solution. The GPS smart antenna will track up to 66 satellites at a time while providing fast time-to-first-fix, one-second navigation update and low power consumption. It can provide you with superior sensitivity and performace even in urban canyon and dense foliage environments. The capabilities meet the sensitivity requirements of car navigation as a well as other location-based applications. Note: The new version of this module uses the MT3329 MTK chipset. Note: Unit does not contain a connector, however there are 5 bare pads you can solder to.
    Part.no: 41004545
    Expected:
    2017-08-29
    Buy
    $74.94

  • GPS-reciever 66 channels MTK3339

      GPS-reciever 66 channels MTK3339
    GPS breakout board with 66 channels and 10Hz update rate. The module is based on GlobalTop PA6H with MediaTek MTK3339 chipset. * -165dBm sensitivity, 66 channels, 10Hz update rate * Built-in ceramic antenna * Datalogging features (stored in on-board flash memory) * Polarity protected supply voltage inputs (3.3 - 5V) * 50mA current consumption with external 3V antenna, 30mA with onboard antenna * SMA connector for external antenna * LEDs for indication of 3DFix (red) and PPS (blue)
    Part.no: 41012615
    In stock: 7 
    Buy
    $39.64

  • Venus GPS Logger with SMA Connector

      Venus GPS Logger with SMA Connector
    The smallest, most powerful, and most versatile GPS receiver we carry just got more powerful. The Venus638FLPx is the successor to the Venus634LPx and has improved sensitivity and a faster update rate. The new module can be configured to an amazingly powerful 20Hz update rate. With 29mA operating current and high sensitivity, this receiver seriously opens new doors for tracking. Module outputs the standard NMEA-0183 or SkyTraq Binary sentences at a default rate of 9600bps (adjustable to 115200bps). The Venus638FLPx has improved sensitivity, an integrated LNA (with multipath detection and suppression), built-in RTC, and integrated single power supply making it very simple to use. Not sure which GPS module is right for you? Check out our GPS Buying Guide! Features: 20Hz Update rate -148dBm cold start sensitivity -165dBm tracking sensitivity 29 second cold start TTFF 3.5 second TTFF with AGPS 1 second hot start 2.5m accuracy Multipath detection and suppression Jamming detection and mitigation SBAS (WAAS / EGNOS) support 67mW full power navigation Works directly with active or passive antenna Supports external SPI flash memory data logging IC 32M Serial Flash Memory Complete receiver in 10mm x 10mm x 1.3mm size Contains LNA, SAW Filter, TCXO, RTC Xtal, LDO Can be powered by a 3.7V LiPo battery (or any 3.5 - 12V supply) through the JST connector or 3.3V regulated supply. Dimensions: 1.25 x 0.75 inches
    Part.no: 41010013
    In stock: 1 
    Buy
    $75.78

  • Venus GPS with SMA connector

      Venus GPS with SMA connector
    This is the latest version of our Venus GPS board; the smallest, most powerful, and most versatile GPS receiver we carry. It's based on the Venus638FLPx, the successor to the Venus634LPx. The Venus638FLPx outputs standard NMEA-0183 or SkyTraq Binary sentences at a default rate of 9600bps (adjustable to 115200bps), with update rates up to 20Hz! The Venus638FLPx also allows for limited on-chip logging (check out the firmware below), as well as external logging using a SPI flash memory chip (not included). This board includes a SMA connector to attach an external antenna (required and not included, see the related items below), and headers for 3.3V serial data, NAV (lock) indication, Pulse-Per-Second output, and external Flash support. We've also provided solder jumpers to easily configure the power consumption, boot memory, and backup supply. This board requires a regulated 3.3V supply to operate; at full power the board uses up to 90mA, at reduced power it requires up to 60mA. We've made it easy to connect an external battery or super capacitor to the board, to support very fast restarts after power is removed. There are even pads on the bottom of the board for the 0.2F supercap (not included but you can find it in the related items below), which will keep the board hot-startable for up to 7 hours without power! Note: We've broken out the pins for the Venus638FLPx's second serial port (RX1,TX1) and I2C interface (SDA,SCL). However, these ports are not used by the stock firmware. SkyTraq offers an SDK allowing the creation of customized firmware; contact them for details. Features: Up to 20Hz update rate -148dBm cold start sensitivity -165dBm tracking sensitivity 29 second cold start TTFF 3.5 second TTFF with AGPS 1 second hot start 2.5m accuracy Multipath detection and suppression Jamming detection and mitigation SBAS (WAAS / EGNOS) support 67mW full power navigation Works directly with active or passive antenna Internal flash for optional 75K point data logging Supports external SPI flash memory data logging Complete receiver in 10mm x 10mm x 1.3mm size Contains LNA, SAW Filter, TCXO, RTC Xtal, LDO Single 2.7-3.3V supply Dimensions: 1.15 x 0.7 inches
    Part.no: 41010016
    In stock: 2 
    Buy
    $63.73