Embedded systems

Embedded systems and single board computer products

Choose Subcategory

ChipKit (‏17)
Pinguino (‏5)
Duinomite (‏7)
ARM (‏27)
Intel Edison (‏9)
Teensy (‏13)
AVR (‏12)
Olinuxino (‏43)
Wearable (‏53)
BBC micro:bit (‏22)
Other (‏27)
BeagleBone (‏11)
PIC (‏24)

Featured products

  Gertboard v2 GPIO expansion board for Raspberry Pi
The Gertboard is an add-on board that extends the use of Raspberry Pi to devices in the real world, including motor/lamp control, and the sensing of voltages and currents. It also contains a host micro that can be programmed with code written and compiled for it, on the Raspberry Pi. The Gertboard comes with a large variety of components, including buttons, LEDs, A/D and D/A converters, a motor controller, and an Atmel AVR microcontroller.
$72.17
Buy
  Beaglebone proto cape
Add some circuitry to your Beagle Bone with our lovely Proto Cape. If you have a 'Bone you need one of these! This PCB fits neatly on top of a Beagle Bone, without getting in the way of the Ethernet jack, and provides a breakout to both 46 pin headers - with individual numbering to keep them straight. We also threw down some strips to access the 5V and 3V power supplies as well as two SMT breakouts, one for SOIC-8's and one for SOT-23's. Kit comes with a double-sided FR4 PCB and 3 sticks of header. You'll need to place the header into the Beagle Bone and then solder the Proto Cape PCB in place, but its very easy and should take only 10 minutes max even for beginners. Beagle Bone is not included! We do have 'Bones in the shop available for purchase separately.
$15.54
Buy
  RFDuino - PCB USB
This is the RFduino PCB USB Shield, a small add-on board that plugs into any USB port and is used to load your sketches onto an RFduino module. This shield is almost identical to the RFduino USB Shield and provides the same basic function. The PCB USB Shield can be attached to any solderless breadboard with the RFduino DIP plugged on top or even below it for better ease of use. Once your code is loaded onto the RFduino, this USB Shield can be detached! On-board the RFduino PCB USB Shield is a 3.3V regulator which can be used to supply power to the RFduino DIP module as well as other shields and possibly the rest of your circuit. Note: This board or the PCB Shield are required to load code onto your RFduino. Features: FT231XQ-R USB Controller Max Current: 500mA Serial Interface: RX, TX, RESET
$32.41
Buy
  PiTFT Plus 320x240 2.8" TFT with capacitive touch
Is this not the cutest little display for the Raspberry Pi? It features a 2.8" display with 320x240 16-bit color pixels and a capacitive touch overlay. That's right, instead of a resistive touchscreen, which requires a fingernail or stylus, you can now use a fingerpad. The screen looks much nicer, with a black bezel and glass overlay. If you don't need a capacitive touchscreen, check out the resistive touch version. This updated design fits perfectly onto the Pi Zero, Pi 3, Pi 2 or Model A+, B+! (Any Pi with a 2x20 connector) Not for use with an old Pi 1 with 2x13 connector If you'd like to use a 2.8" display with the original Pi A or Pi B, check out the Model B version. This version also has all 40 pins GPIO pins brought out so you can connect a 40-pin GPIO cable underneath. Now that it's the same outline as a Pi 3/2/B+ it fits well on top of a Pi in our Raspberry Pi Enclosure base and can use our faceplate for a compact touchscreen Pi The display and touchscreen uses the hardware I2C Pins (SDA & SCL), SPI pins (SCK, MOSI, MISO, CE0) as well as GPIO #25 and #24. All other GPIO are unused and you can still share the I2C pins with sensors, LED drivers, etc. Since we had a tiny bit of space, there's 4 slim tactile switches wired to four GPIOs, that you can use if you want to make a basic user interface. For example, you can use one as a power on/off button. Use it for console access or easily pop up X11 onto the PiTFT for a mini monitor, although its rather small at 320x240. Instead, we recommend using PyGame or other SDL-drawing programs to write onto the frame buffer. Raspberry Pi computer and enclosure not included! As of July 22nd, 2015 this display comes fully assembled with tactile switches too
$60.12
Buy