Click boards

Click boards
Click boards from Mikroelektronika ...
Showing 1 to 50 of 156 matching products
Sort by
 
  • 10 DOF click

      10 DOF click
    10DOF measures rotation, magnetic fields, acceleration and pressure (10 degrees of freedom). The two chips, BNO055 and BMP180 together provide a gyroscope, accelerometer and magnetometer (each with three axes) and a highly accurate pressure sensor. The on-board 32-bit ARM® Cortex®-M0 MCU includes the Bosch Sensortec sensor algorithms. * Communicates over I2C. * Runs on 3.3V. * Acceleromater range (selectable): ±2g/±4g/±8g/±16g. 14 bits. * Gyroskope sensitivity ±125º/s to ±2000º/s. 16 bits. * Magnetometer sensitivity: ±1300µT (x, y-axis), ±2500µT (z-axis). * Pressure sensor range: 300-110hPa (+9000M to -500M, relating to sea level). * Compatible with mikroBUS.
    Part.no: 41014874
    In stock: 3 
    Buy
    $65.90

  • 3D Hall Click

      3D Hall Click
    3D Hall click is based on the MLX90333 Triaxis Hall sensor and can detect the position of nearby magnets. This is accomplished by sensing along three axes (X, Y, Z), and the board can thus measure rotation, linear motion, and 3d position for any suitable magnet. The contactless design is appropriate for weather sealing, dust protection and reduced wear. On-chip signal processing helps with integration with a microcontroller (MCU). Communication with the main board is done over the mikroBUS SPI interface (CS, SCK, MISO, MOSI). The board is designed for use with a 5V power supply.
    Part.no: 41014473
    Currently not in stock
    Buy
    $33.61

  • 3G click (for Europe and Australia)

      3G click (for Europe and Australia)
    Part.no: 41014986
    In stock: 1 
    Buy
    $119.64

  • 4-20 mA R click

      4-20 mA R click
    4-20mA R Click is an add-on board in mikroBUS form factor which serves as a receiver in a 4-20mA current loop standard. It features INA196 current shunt monitor, MCP3201 12-bit ADC as well as TPS61041 DC/DC boost converter. It receives output current (4-20mA) from transmitter and converts it into a voltage (0.4-2V). This voltage is converted into a 12-bit data signal in the MCP3201 A/D converter and sent via mikroBUS SPI lines. Together with 4-20mA T Click this board forms a complete 4-to-20mA current loop standard. It is designed to use either 3.3V or 5V power supply. The board receives output current (4-20mA) from transmitter and converts it into a voltage (0.4-2V). 3.3V or 5V power supply. Features MCP3201, 12-bit ADC with SPI communication interface. On-board screw terminal for easier connection.
    Part.no: 41014245
    In stock: 1 
    Buy
    $34.94

  • 4-20 mA T click

      4-20 mA T click
    4-20mA T Click is an add-on board in mikroBUS form factor. Its a compact and easy solution for adding 4-to-20mA industry standard communication protocol to your design. It features ADuM1411 Quad-chanel digital isolator, MCP4921 12-bit DAC as well as XTR116 4-20mA current loop transmitter. 4-20mA T Click communicates with target board microcontroller via three mikroBUS SPI lines (SDI, SCK, CS). Together with 4-20mA R Click this board forms a complete 4-to-20mA current loop standard. The board is designed to use 3.3V and 5V power supply. LED diode indicates the presence of power supply. The board receives the input digital signal from the microcontroller and sets the output loop current (4-20mA). SPI communication interface. Galvanic isolation provided through ADuM1411 optocoupler. On-board screw terminal for easier connection.
    Part.no: 41014215
    In stock: 2 
    Buy
    $34.94

  • 4G LTE-E click (Europe)

      4G LTE-E click (Europe)
    4G LTE-E click carries the LARA-R211 multi-mode cellular module from u-blox. The board is designed to use 5V power supply. I/O voltage levels could be 3.3V or 5V. It communicates with the target microcontroller over UART interface, with additional functionality provided by the following pins on the mikroBUS line: AN, RST, CS, PWM, INT. With a range of interface options and an integrated IP stack, the modules are designed to support a wide range of data-centric applications. The unique combination of performance and flexibility make these modules ideally suited for medium speed M2M applications, such as smart energy gateways, remote access video cameras, digital signage, telehealth, and telematics. The board has a rich set of components to simplify development: two SMA connectors, a MicroUSB port, as well as a SIM card slot. The LARA-R211 module specifies data rates of up to 10.3 Mb/s for Download, and 5.2 Mb/s for Upload. The network protocol stack includes support for TCP, UDP, PPP, MMS, FTP, SMTP, SMTPS, HTTP, HTTPS, PING, and SSL. It covers following LTE bands: 3, 7, 20. Antenna interfaces - The module has two RF pins with a characteristic impedance of 50 O. The primary antenna pin (ANT1) supports both Tx and Rx, providing the main antenna interface, while the secondary antenna pin (ANT2) supports Rx only for the LTE Rx diversity configuration. A diversity antenna only covers the Rx frequencies, and its job is to acquire an independent sample of data. The application in which you are using the click board can then choose the receive signal it wants to use. u-blox offers m-centre, a free evaluation software for all their cellular modules. It is an easy to use graphical interface where you can configure the module and save the changes on EPROM. You can also view and edit SIM phonebook entries, send text messages, and communicate with the wireless module using AT commands. Simply put 4G is the fourth generation of the cellular network standard. This fourth generation does not support traditional circuit-switched telephony service, but all IP based communication such as IP telephony. If you are not familiar with cellular network standards and protocols and are not sure whether you need GSM or 3G or 4G, read our learn.mikroe.com article about 2G/3G/4G to get a better understanding. LTE or Long Term Evolution, or 4G LTE as it is most commonly called has different categories defined. There are nine different ones so far. LARA-R211 module supports the LTE Cat 1. Key features LARA-R211 cellular module Data rates of up to 10.3 Mb/s for Download Data rates of up to 5.2 Mb/s for Upload Covering the following LTE bands: 3, 7, 20 SMA antenna connectors Micro USB connector Micro SIM card holder UART interface 5V power supply
    Part.no: 41015749
    Currently not in stock
    Buy
    $154.58

  • 7seg click

      7seg click
    7seg click is an accessory board in mikroBUS form factor. Its a compact and easy solution for adding 2-digit seven-segment display to your device. It features two 74HC595 8-bit serial-in, parallel-out shift register modules as well as two seven-segment digits. 7seg Click communicates with target board via SPI interface. It has a LED diode (GREEN) that indicates the presence of power supply. SMD jumper is available for selecting whether board will be operating on 3.3V or 5V power supply. Two 7 segment digits on-board. Two 74HC595 serial-in parallel-out shift registers with SPI interface. Board can be operating on either 3.3V or 5V power supply, which is selectable via SMD jumper. Power indicator LED is available on-board.
    Part.no: 41014192
    In stock: 5 
    Buy
    $13.49

  • 7x10 R click

      7x10 R click
    7x10 R click carries a matrix of 70 red LEDs driven by a pairs of 8-bit serial-in, parallel-out shift registers, a Darlington Transistor array and a Johnson counter. 7x5 is a standard resolution for displaying ASCII characters, so 7x10 click is essentially a dual-character display capable of showing letters in more readable typefaces compared to a 14-segment display. The click communicates with the target MCU through the mikroBUS SPI interface (SCK, SDO, SDI), with additional functionality provided by R CLK, MR#, LATCH and R RST pins. 7x10 R click is designed to use either a 3.3V or a 5V power supply. A pair of red 7x5 LED matrices SPI interface (plus MR#, LATCH and R RST pins) 3.3V or 5V power supply
    Part.no: 41014477
    Currently not in stock
    Buy
    $20.12

  • 8x8 B click

      8x8 B click
    8x8 B Click is an add-on board in mikroBUS form factor. Its a compact and easy solution for adding 8x8 BLUE LED display matrix to your design. It features MAX7219 8-digit LED display driver module as well as 64 BLUE LED diodes. 8x8 B Click communicates with target board microcontroller via four mikroBUS SPI lines (DIN, DOUT, CLK and CS). The board is designed to use 5V power supply only, but it can be used with 3.3V MCUs as well. The MAX7219 is serial input/output common-cathode display driver with SPI interface. Analog and digital brightness control. On-chip BCD code-B decoder. Board is powered with 5V power supply only, but can be used with 3.3V MCUs as well.
    Part.no: 41014225
    In stock: 2 
    Buy
    $24.22

  • 8x8 G click

      8x8 G click
    8x8 G Click is an add-on board in mikroBUS form factor. Its a compact and easy solution for adding 8x8 GREEN LED display matrix to your design. It features MAX7219 8-digit LED display driver module as well as 64 GREEN LED diodes. 8x8 G Click communicates with target board microcontroller via four mikroBUS SPI lines (DIN, DOUT, CLK and CS). The board is designed to use 5V power supply only, but it can be used with 3.3V MCUs as well. The MAX7219 is serial input/output common-cathode display driver with SPI interface. Analog and digital brightness control. On-chip BCD code-B decoder. Board is powered with 5V power supply only, but can be used with 3.3V MCUs as well.
    Part.no: 41014224
    In stock: 2 
    Buy
    $20.12

  • 8x8 R click

      8x8 R click
    8x8 R Click is an add-on board in mikroBUS form factor. Its a compact and easy solution for adding 8x8 RED LED display matrix to your design. It features MAX7219 8-digit LED display driver module as well as 64 RED LED diodes. 8x8 R Click communicates with target board microcontroller via four mikroBUS SPI lines (DIN, DOUT, CLK and CS). The board is designed to use 5V power supply only, but it can be used with 3.3V MCUs as well. The MAX7219 is serial input/output common-cathode display driver with SPI interface. Analog and digital brightness control. On-chip BCD code-B decoder. Board is powered with 5V power supply only, but can be used with 3.3V MCUs as well.
    Part.no: 41014214
    In stock: 1 
    Buy
    $20.12

  • 8x8 Y click

      8x8 Y click
    8x8 Y Click is an add-on board in mikroBUS form factor. Its a compact and easy solution for adding 8x8 YELLOW LED display matrix to your design. It features MAX7219 8-digit LED display driver module as well as 64 YELLOW LED diodes. 8x8 Y Click communicates with target board microcontroller via four mikroBUS SPI lines (DIN, DOUT, CLK and CS). The board is designed to use 5V power supply only, but it can be used with 3.3V MCUs as well. The MAX7219 is serial input/output common-cathode display driver with SPI interface. Analog and digital brightness control. On-chip BCD code-B decoder. Board is powered with 5V power supply only, but can be used with 3.3V MCUs as well.
    Part.no: 41014213
    In stock: 2 
    Buy
    $20.12

  • 9DOF click

      9DOF click
    9DOF click carries STs LSM9DS1 inertial measurement module that combines a 3D accelerometer, a 3D gyroscope and a 3D magnetometer into a single device outputting so called nine degrees of freedom data (3-axis acceleration, angular velocity and heading), in 16-bit resolution. 9DOF click communicates with the target MCU through the mikroBUS I2C interface (SCL and SDA) with additional functionality provided by the programmable Interrupt (INT) pin, as well as the Enable (EN) pin. The IC has multiple interrupt lines which can be accessed through jumpers on the click board. I2C addresses are specified in the same manner. The board uses a 3.3 power supply only. 3-axis accelerometer, 3-axis gyroscope and 3-axis magnetometer in one IC Measuring ±2/±4/±8/±16 g acceleration ±4/±8/±12/±16 gauss magnetic ±245/±500/±2000 dps Multiple interrupt lines Selectable I2C addresss Individual sensors can be powered down to reduce consumption Ready-to-use examples save development time
    Part.no: 41014479
    Currently not in stock
    Buy
    $28.19

  • Accel 3 click

      Accel 3 click
    Part.no: 41014987
    In stock: 3 
    Buy
    $28.19

  • Accel click

      Accel click
    Accel Click is an accessory board in mikroBUS form factor. It features ADXL345 3-axis accelerometer module with ultra-low power and high resolution (13-bit) measurement. Module supports several sensing functions such as single/double tap detection, activity/inactivity monitoring, free-fall detection etc. It has memory management system with a 32-level FIFO buffer to store data with minimized host processor activity. Board is designed to use 3.3V power supply only. Ultralow power consumption: 40 µA in measurement mode and 0.1 µA in standby mode Selectable measurement range of ±2 g, ±4 g, ±8 g, or ±16 g Tap/double tap detection SPI or I2C communication. Embedded FIFO technology minimizes host processor load
    Part.no: 41014185
    In stock: 2 
    Buy
    $25.54

  • Accel2 click

      Accel2 click
    Accel 2 click carries STs LIS3DSH IC, a low-power factory-calibrated three-axis accelerometer which embeds a FIFO buffer and two programmable state machines. It allows you to implement gesture recognition. User-defined programs can distinguish movement patterns like shake and double shake, face up and face down, turn and double turn, and activate an interrupt upon their execution. You can also switch between I2C and SPI interfaces for communicating with the target board MCU (by soldering the onboard jumpers in the appropriate positions). Accel 2 click is designed to use a 3.3V power supply only. LIS3DSH three-axis accelerometer Selectable communication interface (I2C or SPI) FIFO buffer and embedded state machines 3.3V power supply
    Part.no: 41014432
    In stock: 3 
    Buy
    $25.54

  • ADAC click

      ADAC click
    ADAC click is an 8-channel 12-bit ADC/DAC/GPIO for the MikroElektronica development environment. The module is based on the AD5593R from Analog Devices. * Communicates over I2C. * Runs on 3.3V or 5V. * Individually settable modes per channel (ADC, DAC or GPIO).
    Part.no: 41015767
    In stock: 1 
    Buy
    $34.94

  • Adapter click

      Adapter click
    Adapter Click is a breakout board which simplifies connection of add-on boards with IDC10 headers to mikroBUS socket. There are two ways of establishing connection: using male or female IDC10 connectors. Both are provided with the package. You may solder male IDC10 header on the top side of Adapter Click and connect the add-on board directly or via IDC10 flat cable. In some cases, female header socket is a better choice. Solder it either on the top, or the bottom side, depending on which one is more convenient in given circumstances. Each mikroBUS line is covered, except AN and RST. There are two jumpers for SPI/I2C selection and one for selection of power supply range.
    Part.no: 41014133
    In stock: 2 
    Buy
    $8.80

  • ADC click

      ADC click
    ADC Click is an accessory board in mikroBus form factor. It includes a 12-bit Analog-to-Digital Converter (ADC) MCP3204 that features 50k samples/second, 4 input channels and low-power consumption (500nA typical standby, 2µA max). Board uses industry standard SPI communication interface. It is small in size and features convenient screw terminals for easier connections. Board is set to use 3.3V power supply by default. Place PWR SEL SMD jumper to 5V position if used with 5V systems. 12-bit resolution of Analog-to-Digital conversion Up to 50K samples per second 4 input channels Low power consumption (500nA typical standby) Communication is done using industry standard Serial Peripheral Interface (SPI).
    Part.no: 41014691
    Currently not in stock
    Buy
    $32.29

  • ADC3 click

      ADC3 click
    ADC3 click carries Microchips MCP3428 16-bit multichannel analog-to-digital converter. The click has four pairs of screw terminals onboard, letting you access the chips four differential input channels. At the highest resolution of 16-bits, the chip outputs conversion results at 15 samples per second. At 14-bits, the sample rate is 60 SPS. Maximum conversion speed is achieved in 12-bit mode, 240 samples per second. A pair of onboard jumpers allow switching between different I2C addresses. ADC3 click communicates with the target MCU through mikroBUS I2C pins (SCL, SDA). It is designed to use either a 3.3V or 5V power supply. Four channel 16-bit ADC Selectable I2C addresses Sample rate up to 240 SPS 3.3V or 5V power supply.
    Part.no: 41014423
    Currently not in stock
    Buy
    $29.52

  • Air Quality click

      Air Quality click
    Air quality click carries an MQ-135 sensor for detecting poisonous gases that impact air quality in homes and offices. The gas sensing layer on the sensor unit is made of tin dioxide (SnO2), which has lower conductivity in clean air. The conductivity increases with air pollution. The sensor reacts to ammonia (NH3), nitrogen oxides (NOx), benzene, smoke, CO2 and other harmful gases. To calibrate the sensor for the environment youll be using it in, Air quality click has a small potentiometer that allows you to adjust the load resistance of the sensor circuit. Air quality click communicates with the target board through AN (OUT) mikroBUS line. Its designed to use a 5V power supply only. MQ-135 high-sensitivity Air quality sensor. Potentiometer for calibration. Designed to use a 5V power supply.
    Part.no: 41014334
    Currently not in stock
    Buy
    $22.17

  • Alcohol click

      Alcohol click
    Alcohol click carries an MQ-3 Semiconductor sensor for alcohol. The gas sensing layer on the sensor unit is made of Tin dioxide (SnO2), an inorganic compound which has lower conductivity in clean air. The conductivity increases as the levels of alcohol gas rise. Alcohol click has a high sensitivity to alcohol and it can be used to detect alcohol in concentrations from 0.04 to 4mg/l. To calibrate the sensor for the environment youll be using it in, Alcohol click has a small potentiometer that allows you to adjust the Load Resistance of the sensor circuit. Alcohol click communicates with the target board through AN (OUT)mikroBUS line. Its designed to use a 5V power supply only. MQ-3 high-sensitivity alcohol sensor. Potentiometer for calibration. Designed to use a 5V power supply.
    Part.no: 41014315
    In stock: 1 
    Buy
    $20.12

  • Altitude click

      Altitude click
    Altitude click features a MEMS pressure sensor MPL3115A2, which provides accurate pressure/altitude (20-bit) and temperature (12-bit) data. Resolution is down to 30 cm (1.5 Pa). The MPL3115A2 contains automatic internal data processing with data acquisition and compensation. It features 32 sample FIFO buffer to minimize the overhead of collecting multiple data samples. It can autonomously collect data at programmed intervals and store it up to 12 days depending on data acquisition rate (1 second - 9 hour). Board uses I2C communication interface and is designed to use 3.3V power supply only. Pressure range: 20 - 110 kPa. 20-bit altitude measurement (meters), 12-bit temperature measurement. Compensated, direct reading (software is not needed). I2C communication interface.
    Part.no: 41014286
    In stock: 1 
    Buy
    $19.52

  • Ambient 2 click

      Ambient 2 click
    Ambient 2 click carries TIs OPT3001 Ambient Light sensor. Its a small (2mm x 2mm) single-chip lux meter that measures only the visible part of the light spectrum from any kind of source (mimicking the way humans see light). It does so by filtering out 99% of infrared light. The measurement range of Ambient 2 click is from 0.01 Lux to 83k lux, and a 23-bit resolution. Communication with the target MCU is done through mikroBUS I2C pins, with an additional INT pin which can be used for triggering wake-up events (offloading the MCU). Key features Measures visible light (filtering out 99% of IR) 0.01 lux to 83k lux range, 23-bit resolution I2C interface, plus INT pin 3.3V power supply
    Part.no: 41014431
    Currently not in stock
    Buy
    $18.80

  • BarGraph click

      BarGraph click
    BarGraph Click is a compact and easy solution for adding ten-segment light bar display to your design. It features JSB-R102510Z light bar display as well as two 74HC595 shift registers. The 74HC595 IC contains an 8-bit serial in, parallel/serial-out shift register as well as 8-bit storage register. BarGraph Click communicates with the target board microcontroller via mikroBUS SPI (MOSI, MISO, SCK, CS), RST and PWM lines. Provided SMD jumper allows user to select whether the board will be powered with 3.3V or 5V power supply. Serial SPI interface saves microcontroller pins. LED light intensity can be controlled over PWM. Supports either 3.3V or 5V power supply.
    Part.no: 41014257
    In stock: 1 
    Buy
    $16.14

  • BEE click

      BEE click
    BEE Click is an accessory board in mikroBus form factor. It features 2.4 GHz IEEE 802.15.4 radio transceiver module MRF24J40MA. This module includes an integrated PCB antenna and matching circuitry and is connected to the microcontroller via a SPI interface. As such, this module is an ideal solution for wireless networks, smart home automation, building automation and other electronic applications that need wireless communication. Board is designed to use 3.3V power supply only. IEEE 802.15.4 Standard Compliant RF Transceiver Supports ZigBee®, MiWi, MiWi P2P and Proprietary Wireless Networking Protocols Integrated 20 MHz and 32.768 kHz Crystal Oscillator Circuitry Data Rate: 250 kbps (IEEE 802.15.4); 625 kbps (Turbo mode)
    Part.no: 41014709
    Currently not in stock
    Buy
    $39.04

  • BLE2 click

      BLE2 click
    BLE2 click is a simple solution for adding Bluetooth 4.1 (also known as Bluetooth Low Energy, BLE, Bluetooth Smart) to your design. It features the RN4020 module from MicroChip that has the complete Bluetooth stack, and can act both as a client or a server. Additionally, the RN4020 module supports 13 public profiles and 17 public services, including the MicroChip Low-energy Data Profile (MLDP). BLE 2 communicates with the target board microcontroller through mikroBUS RX, TX and AN (here, CMD), PWM (con.), and RST (wake) lines. The board is designed to use a 3.3V power supply only. RN4020 Bluetooth 4.1 module. Integrated TCP/IP stack. PCB antenna. 3.3V power supply.
    Part.no: 41014354
    In stock: 5 
    Buy
    $40.36

  • Bluetooth Click

      Bluetooth Click
    BLUETOOTH Click is an accessory board in mikroBus form factor. Enrich your device with bluetooth capability with up to 100m range. Board offers low power, highly economic Bluetooth radio for adding wireless capability to your products. On-board RN-41 module with UART interface is easy and simple to use. Board is designed to use 3.3V power supply only. Fully qualified Bluetooth 2.1/2.0/1.2/1.1 module Low power (30mA connected, less than 10mA sniffmode) UART (SPP or HCI) data connection interface. UART Data rates up to 3Mbps.
    Part.no: 41014700
    In stock: 3 
    Buy
    $52.41

  • Bluetooth2 click

      Bluetooth2 click
    Bluetooth2 Click features BLUEGIGA WT41 Bluetooth® 2.1 module with operating range of 1000m (between two WT41 modules). It is equipped with iWRAP firmware which enables users to access Bluetooth® functionality with simple ASCII commands delivered to the module. It supports up to 14 Bluetooth profiles. Board is ideal for developers who want to integrate Bluetooth® wireless protocol with limited knowledge of Bluetooth® and RF technologies. It uses four UART interface lines and is designed to use 3.3V power supply only. Fully qualified Bluetooth 2.1+ EDR module. Exceptional radio performance (TX power: +20 dBm, RX sensitivity: -90 dBm). UART (HCI) data connection interface. Includes iWRAP firmware with all relevant Bluetooth profiles and simple control interface.
    Part.no: 41014247
    In stock: 2 
    Buy
    $79.28

  • BT Audio click

      BT Audio click
    Module for sending and receiving audio over bluetooth, based on RN52 from Microchip. Audio source and speaker/amplifier I/O through 3.5mm mini jacks. The RN52 chip delivers high sound quality and has a built in DSP which is configured using simple ASCII commands. The module also supports HSP/HFP, (Handsfree/Headset Profile) A2DP, AVRCP, SPP and digital I/O. Support for aptX ensures high CD quality audio (16 bit 44.1kHz). Also supports iAP for use with Apple devices such as iPad, iPhone, iPod and mac computers. BT Audio click has a range of 10 meters in open spaces, plenty for most indoor applications. Communication with the main board is done using mikroBUS UART. Runs off 3.3V Dimensions: 57.15 x 25.4mm
    Part.no: 41015780
    In stock: 2 
    Buy
    $65.90

  • Button R click

      Button R click
    Button R click is the simplest solution for adding a single pushbutton to your design. The button itself is transparent, 6.8mm in diameter and has a red LED backlight. When pressed, it sends an interrupt signal to the target board microcontroller. The backlight LED is controlled separately through the mikroBUS PWM pin, so you can program all kinds of patterns (varying level of light intensity or rate of blinking on subsequent button presses). The board can use either a 3.3V or a 5V power supply. Transparent pushbutton Red LED backlight Uses mikroBUS INT (for pushbutton) and PWM (for LED) pins 3.3V or 5V power supply
    Part.no: 41014429
    Currently not in stock
    Buy
    $13.25

  • CAN SPI click 3.3V

      CAN SPI click 3.3V
    CAN SPI click 3.3V is an accessory board in mikroBus form factor. It is the best solution to add CAN connectivity to your microcontroller with SPI interface. Board features SN65HVD230 can transciever circuit which provides CAN serial communication physical layer in accordance with the ISO 11898 standard. It is designed for operation in especially-harsh environments, these devices feature cross-wire protection, loss-of-ground and overvoltage protection, overtemperature protection, as well as wide common-mode range. Board is designed to use 3.3V power supply only. Implements ISO-11898 standard physical layer requirements Low-Current Standby Mode 370 µA Typical Supports 1 Mb/s operation Board features screw terminals for easier connectivity, power LED and node termination jumper.
    Part.no: 41014708
    In stock: 4 
    Buy
    $28.19

  • CAN SPI click 5V

      CAN SPI click 5V
    CAN SPI click 5V is an accessory board in mikroBus form factor. It is the best solution to add CAN connectivity to your microcontroller with SPI interface. Board features MCP2551 can transciever circuit which provides CAN serial communication physical layer in accordance with the ISO 11898 standard. It is designed for operation in especially-harsh environments, these devices feature cross-wire protection, loss-of-ground and overvoltage protection, overtemperature protection, as well as wide common-mode range. Board is designed to use 5V power supply only. Implements ISO-11898 standard physical layer requirements Up to 112 nodes can be connected Supports 1 Mb/s operation Board features screw terminals for easier connectivity, power LED and node termination jumper.
    Part.no: 41014710
    In stock: 3 
    Buy
    $28.19

  • Cap Extend click

      Cap Extend click
    Part.no: 41014985
    In stock: 3 
    Buy
    $24.22

  • CapSense click

      CapSense click
    CapSense click add-on board features a capacitive sensing module CY8C201A0 which takes human body capacitance as an input and directly provides the real time sensor information via I2C output. The board contains capacitive sensing elements (5-segment slider and two buttons) as well as two LEDs. The CY8C201A0 capacitive controller has high immunity against radiated and conductive noise. The board is designed to use 3.3V or 5V power supply. This is determined by the position of SMD jumper J1. Low operating current (continuous sensor scan: 1.5 mA, deep sleep current: 4 µA). High sensitivity, immunity to RF and AC noise, Robust sensing algorithm. Run time reconfigurable over I2C.
    Part.no: 41014270
    In stock: 2 
    Buy
    $21.45

  • ccRF click

      ccRF click
    ccRF click is a low-power 2.4 GHz transceiver designed for the 2400- 2483.5 MHz ISM and SRD frequency bands. It features CC2500 Low-Power 2.4 GHz RF transceiver as well as PCB trace antenna. The CC2500 is integrated with a highly configurable baseband modem that supports various modulation formats and has data rate up to 500 kBaud. Maximum device range is up to 20 meters in open space. ccRF click communicates with the target microcontroller via mikroBUS SPI, RST and PWM lines. The board is designed to use 3.3V power supply only. All these features make this board ideal for consumer electronics, wireless audio, wireless keyboard and mouse RF remote controls. Key features High sensitivity (-104 dBm at 2.4 kBaud, 1% packet error rate) Frequency range: 2400 - 2483.5 MHz Low current consumption (13.3 mA in RX, 250 kBaud). Programmable data rate from 1.2 to 500 kBaud.
    Part.no: 41014264
    In stock: 1 
    Buy
    $29.52

  • Charger click

      Charger click
    Part.no: 41014997
    In stock: 3 
    Buy
    $29.52

  • click USB adapter

      click USB adapter
    Click USB adapter board provides the necessary interface for connecting Click add-on boards to your PC through high speed USB connection, without the need for microcontroller as a mediator. It features FT2232H dual high speed USB to multipurpose IC, Analog-to-Digital converter, EEPROM memory and a single mikroBUS host socket. Click USB adapter board can be powered through USB cable only. Two jumpers are provided on board. J1 jumper is used to select whether UART or I2C will be used. J2 selects whether AN pin on mikroBUS socket will be GPIO pin, or connected to MCP3204 AD converter circuit. Key features FT2232H provides necessary communication lines defined by the mikroBUS standard. On-board circuitry generates 3.3V and 5V. MCP3204 AD converter brings support for analog input. Power and RX/TX LEDs on-board.
    Part.no: 41014262
    In stock: 1 
    Buy
    $39.04

  • CO click

      CO click
    CO click carries an MQ-7 sensor for Carbon monoxide. The gas sensing layer on the sensor unit is made of Tin dioxide (SnO2), which has lower conductivity in clean air. The conductivity increases as the levels of Carbon monoxide rise. The detection range of the sensor is 20ppm-2000ppm of CO. To calibrate the sensor for the environment youll be using it in, CO click has a small potentiometer that allows you to adjust the Load Resistance of the sensor circuit. For precise calibration the sensor needs to preheat (once powered up, it takes 48h to reach the right temperature). CO click communicates with the target board through AN (OUT) mikroBUS line. Its designed to use a 5V power supply only. MQ-7 high-sensitivity CO sensor. Potentiometer for calibration. Designed to use a 5V power supply.
    Part.no: 41014330
    In stock: 1 
    Buy
    $22.17

  • Color 2 Click

      Color 2 Click
    Color 2 click carries the ISL29125 RGB color light sensor. It detects red, green and blue in a variety of lighting conditions, outputting 16-bit resolution data in a measuring range from 5.7 m lux to 10,000 lux. Both the range and output resolution are selectable (narrower vs wider bandwidth, 12 vs 16 bit). The sensor also incorporates a IR blocking filter, allowing Color 2 click to work even under a dark glass cover. The integrated ADC also rejects 50Hz and 60Hz flicker from artificial light sources. The board communicates with the target MCU through the mikroBUS I2C interface (SCL and SDA pins). A programmable interrupt pin is also available. The board is designed to use a 3.3V power supply only. Key features 16 bit RGB color sensor 5.7 m lux -10,000 lux range IR blocking filter I2C interface Key Benefits Selectable resolution ADC rejects 50Hz and 60Hz flicker from artificial sources Ready-to-use examples save development time Supported in all MikroElektronika compilers
    Part.no: 41014474
    Currently not in stock
    Buy
    $21.45

  • Color click

      Color click
    Color click is a compact and easy solution for adding color sensing to your design. It features TCS3471 color light sensor as well as RGB LED diode. The TCS3471 features red, green, blue, and clear light sensing (RGBC) that detects light intensity under a variety of lighting conditions and through a variety of attenuation materials. RGB LED is provided to help you illuminate the objects if no other light source is available. Color click communicates with the target board microcontroller via mikroBUS I2C (SDA, SCL) and INT lines. The board is designed to use 3.3V power supply only. Very High Sensitivity - Ideally Suited for Operation Behind Dark Glass. Resolution Up to 16 Bits. Programmable Analog Gain, Integration Time, and Interrupt Function with Upper and Lower Thresholds.
    Part.no: 41014266
    In stock: 1 
    Buy
    $20.12

  • Comparator click

      Comparator click
    Comparator click, carrying the LM2903 IC, has two independent precision voltage comparators. Two pairs of screw terminals allow you to connect separate inputs (additional two screw terminals are for GND connections). You can use it either with a single (range of 2.0 VDC to 36 VDC) or dual power supply (from ±1.0 VDC to ±18 VDC). Two potentiometers are placed between the terminals and the IC. Each input has its own Interrupt pin on the mikroBUS socket (one on the INT pin, the other in place of the mikroBUS AN pin), here marked 01 and 02. Key features LM2903 low power dual voltage comparator Two pairs of input screw terminals and two potentiometers Range: 2-36 VDC (single power supply); ±1.0 VDC- ±18 VDC (dual power supply) 3.3V or 5V voltage level
    Part.no: 41014441
    Currently not in stock
    Buy
    $16.14

  • Compass click

      Compass click
    Compass Click is an add-on board in mikroBUS form factor. It features LSM303DLHC ultra compact high performance e-compass module. It includes specific sensing element and an IC interface capable of measuring both linear acceleration (full-scale of ±2g/±4g/±8g/±16g) and magnetic field (From ±1.3 to ±8.1 gauss full-scale) and provides a 16-bit data output through I2C interface. Readings received from the IC can be processed and used to determine earths magnetic north pole. The board is designed to use 3.3V power supply only. All these features make this board ideal for compensated compass, position detection, map rotation, pedometer, display orientation and many more. 3 magnetic field channels and 3 acceleration channels. ±1.3 to ±8.1 gauss magnetic field fullscale and ±2g / ±4g / ±8g / ±16g selectable full-scale. I2C serial bus interface, 16 bit data output. 2 independent programmable interrupt generators for free-fall and motion detection.
    Part.no: 41014244
    In stock: 4 
    Buy
    $33.61

  • Counter Click

      Counter Click
    Counter click carries an LS7366R 32-bit quadrature counter. The top of the board has a pinout for interfacing with incremental encoders. The interface has ENCA and ENCB pins, along with ENCI, which is a programmable index. The A and B pulses fron an encoder are out of phase to each other, ideally by 90º. The LS7366R CMOS counter takes these signals as inputs and decodes them for determining direction and speed. On the other side, Counter click communicates with the target board microcontroller through the mikroBUS SPI interface (CSK, MISO, MOSI), plus enable (CNT EN) and interrupt (LFLAG) pins. The board can use either a 3.3V or a 5V power supply. 32-bit quadrature encoder Pinout for receiving A and B pulses from incremental encoders SPI interface with additional Enable and Interrupt pins 3.3V or 5V power supply
    Part.no: 41014442
    In stock: 2 
    Buy
    $33.61

  • Current click

      Current click
    Current Click is an add-on board used for measurement of electric current. It features INA196 current shunt monitor, MCP3201 12-bit ADC, MAX6106 voltage reference as well as two screw terminals. Board receives current from the output circuit connected to IN(+) and OUT(-) pins of the first screw terminal. INA196 IC converts this current into a voltage. Second screw terminal is used for external shunt. In order to measure current values in various bands, you need to provide the shunt of the appropriate value. Four shunts with different values are provided in the package. Current Click communicates with target microcontroller via mikroBUS SPI or AN lines. Its designed to use either 3.3V or 5V power supply. Complete current sense solution. Supports bandwidth up to 500kHz. Selectable AN or SPI communication interface. Four shunts provided in the package: 0.05O, 0.2O, 1O and 10O. On-board screw terminals for easier connection.
    Part.no: 41014248
    In stock: 2 
    Buy
    $32.29

  • DAC 3 click

      DAC 3 click
    Part.no: 41014995
    In stock: 2 
    Buy
    $24.22

  • DAC Click

      DAC Click
    DAC Click is an accessory board in mikroBus form factor. It includes a 12-bit Digital-to-Analog Converter MCP4921 that features an optional 2x buffered output and SPI interface. The board provides high accuracy and low noise performance for industrial applications where calibration or compensation of signals, such as temperature, pressure and humidity, are required. Board is set to use 3.3V power supply by default. Solder PWR SEL SMD jumper to 5V position if used with 5V systems. MCP4921 single channel 12-bit DAC. Output Settling Time 4.5µs. Operating Current 175 µA (typ). Industruy standard SPI serial interface. Easy to connect using provided screw terminals.
    Part.no: 41014697
    In stock: 2 
    Buy
    $24.22

  • DAC2 Click

      DAC2 Click
    DAC2 click carries LTC2601CDD, a 16-bit digital-to-analog converter, along with voltage output screw terminals. The chip has high rail-to-rail output drives (±15mA, Min) and double-buffered data latches. The click board communicates with the target MCU through the mikroBUS SPI interface with clock rates up to 50MHz. Additionally, the CLR pin, in place of default mikroBUS RST pin, clears all the registers. The board uses either a 3.3V or 5V power supply. You can also set the reference voltage either to VCC or 4.096V. 16-bit digital-to-analog converter High rail-to-rail output drives (±15mA, Min) Double buffered data latches SPI interface
    Part.no: 41014443
    Currently not in stock
    Buy
    $25.54

  • DALI Click

      DALI Click
    DALI Click is a compact board that provides Digital Addressable Lighting Interface (DALI) to your design. Board features two optocouplers, push button and screw terminals. DALI Click communicates with target board via four mikroBUS lines (RST, CS, PWM and INT). Data between MCU and devices is transferred over two-wire differential bus by means of asynchronous, half-duplex, serial protocol. It is possible to address up to 64 devices in DALI stand alone systems and more than 64 devices as DALI subsystem (gateways). The board is designed to use 3.3V or 5V power supply. LED diode indicates the presence of power supply. It is possible to address up to 64 devices in DALI stand alone systems and more than 64 devices as DALI subsystem (gateways). The board is designed to use 3.3V or 5V power supply. LED diode indicates the presence of power supply.
    Part.no: 41014216
    Currently not in stock
    Buy
    $33.61

  • DC Motor 2 Click

      DC Motor 2 Click
    DC MOTOR 2 click carries the TB6593FNG driver IC for direct current motors. With two pairs of screw terminals (power supply and outputs), the click board can drive motors with voltages from 2.5 to 13V (output current of up to 1.2 amps with peaks up to 3.2 amps) . The PWM signal drives the motor while the IN1 and IN2 pins provide binary direction signals that set the direction of the motor (clockwise or counter clockwise), or apply stop or short brake functions. Stop mode cuts off the power supply so the motor continues spinning until it runs out of momentum. Short break brings it to an abrupt stop. TB6593FNG motor driver IC Drives motors from 2.5 to 13V Stop, short brake and standby modes 3.3V or 5V power supply
    Part.no: 41014438
    In stock: 2 
    Buy
    $18.80

Pages: 1 2 3 4