Battery LiPo 3.7V 1400mAh

Part.no: 41010263
Manufacturer: Olimex
In stock: 11

Description

INTRODUCTION:

This is rechargable Li-Po high discharge current battery with JST connector ready to plug to OLIMEXINO-328, OLIMEXINO-STM32, PIC32-PINGUINO, PIC32-PINGUINO-OTG, DUINOMITE and DUINOMITE-MEGA. The battery have overcharge and short circuit protection.

FEATURES:

Charge voltage 4.2V, nominal voltage 3.7V, cut-off voltage 3.0V

Max charge current 700mAh

Max discharge current 1400mAh

Impedance 60mOhm at 1KHz

Operating temperature: at charge 0-55C, at discharge -25C+60C

Capacity loss after 500 cycles full charge/discharge at 20C: 20%

Dimensions 50x34x8mm

Customers Who Bought This Item Also BoughtCustomers Also Bought

  • USB-uLIPO - Charger for LiPo batteries

      USB-uLIPO - Charger for LiPo batteries
    INFO: This is low cost and very compact Li-Po battery charger, based on Microchip MCP73833 with three status LEDs it display the battery status, works with batteries up to 5000 mAh. FEATURES: MCP73833 charger miniUSB connector JST 2.0 mm connector for our BATTERY-LIPO1400mAh three status LEDs selectable two charge currents 100/470mA dimensions 30x13 mm (1.18x0.5")
    Part.no: 41010264
    In stock: 7 
    Buy
    49.00

  • Adafruit Feather Huzzah ESP8266

      Adafruit Feather Huzzah ESP8266
    Feather is the new development board from Adafruit, and like it's namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Adafruit Feather HUZZAH ESP8266 - our take on an 'all-in-one' ESP8266 WiFi development board with built in USB and battery charging. Its an ESP8266 WiFi module with all the extras you need, ready to rock! We have other boards in the Feather family, check'em out here. At the Feather HUZZAH's heart is an ESP8266 WiFi microcontroller clocked at 80 MHz and at 3.3V logic. This microcontroller contains a Tensilica chip core as well as a full WiFi stack. You can progam the microcontroller using the Arduino IDE for an easy-to-run Internet of Things core. We wired up a USB-Serial chip that an upload code at a blistering 921600 baud for fast development time. It also has auto-reset so no noodling with pins and reset button pressings. To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. Here's some handy specs! Measures 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) without headers soldered in Light as a (large?) feather - 9.7 grams ESP8266 @ 80MHz with 3.3V logic/power 4MB of FLASH (32 MBit) Built in WiFi 802.11 b/g/n 3.3V regulator with 500mA peak current output CP2104 USB-Serial converter onboard with 921600 max baudrate for uploading Auto-reset support for getting into bootload mode before firmware upload 9 x GPIO pins - can also be used as I2C and SPI 1 x analog inputs 1.0V max Built in 100mA LiPoly charger with charging status indicator LED, can also cut a trace to disable the charger Pin #0 red LED for general purpose blinking. Pin #2 blue LED for bootloading debug & general purpose blinking Power/enable pin 4 mounting holes Reset button Comes fully assembled and tested, with a USB interface that lets you quickly use it with the Arduino IDE or NodeMCU Lua. (It comes preprogrammed with the Lua interpretter) We also toss in some header so you can solder it in and plug into a solderless breadboard. Lipoly battery and USB cable not included (but we do have lots of options in the shop if you'd like!) 23mm x 51mm x 7.2mm / 0.9" x 2" x 0.28" Weight: 6.2g
    Part.no: 41014735
    In stock: 7 
    Buy
    199.00

  • Header PH 2p 2.0mm

      Header PH 2p 2.0mm
    Pin header JST-PH. 2mm pitch. Top entry.
    Part.no: 41004562
    In stock: 115 
    Buy
    1 - 2.23
    10 - 2.01
    25 - 1.67
    100 - 1.34

  • Male header straight 2.54mm 1x40p breakable gold

      Male header straight 2.54mm 1x40p breakable gold
    40-pole male header with 2.54 mm pitch. Can be cut to desired length. Height (frame): 2.54mm Total height: 11.54mm
    Part.no: 41001167
    In stock: 5399 
    Buy
    1 - 9.00
    10 - 8.10
    25 - 6.75
    100 - 4.50

  • Battery charger LiPo Micro-USB

      Battery charger LiPo Micro-USB
    If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The LiPo Charger Basic is stripped down of all features and just does one thing well - charge 3.7V LiPo cells at a rate of 500mA per hour. It is designed to charge single-cell Li-Ion or Li-Polymer batteries. Check the datasheet below to see if it will work with your battery. The board incorporates a charging circuit, status LED, connector for your battery (JST-type used in the batteries we carry), and a micro-USB connector. A small mounting hole allows this charger to be easily embedded into a project. * Dimensions: 29.4 x 10.8mm
    Part.no: 41013014
    In stock: 2 
    Buy
    89.00

  • Hook-up wires w. pins for breadboard - soft 70pcs

      Hook-up wires w. pins for breadboard - soft 70pcs
    Pack of 65pcs jumper wires in assorted lengths and colors. A must in every lab! Fits breadboards. Each cable is terminated with a ø0.5mm pin. Contents: * 45pcs 100mm * 10pcs 150mm * 5pcs 180mm * 5pcs 230mm
    Part.no: 41003181
    In stock: 1085 
    Buy
    1 - 35.00
    10 - 31.50
    25 - 26.25
    100 - 21.00