DCA75 halvledaranalysator

Art.nr: 41015362
I lager: 1

Beskrivning

The DCA Pro has an advanced new design that features a graphics display, USB communications, PC software and an enhanced component identification library.

Features

stand-alone or with a PC

automatic component type identification

automatic pinout identification

special feature identification such as protection diodes and resistor shunts

bipolar transistors: gain and leakage current measurements, silicon and germanium detection

gate threshold measurement for Enhancement Mode MOSFETs

semiconductor forward voltage measurement for diodes, LEDs and

transistor Base-Emitter junctions

automatic and manual power-off

Specifications

Specification Summary at 20°C (68°F) unless otherwise specified

peak test current into short circuit: -5.5 mA to 5.5 mA

peak test voltage across open circuit: -5.1 V to 5.1 V

transistor:

gain range (Hfe): 4 - 65 000

gain accuracy: ± 3% ± 5 Hfe

Vceo test voltage: 2.0 V - 3.0 V

Vbe accuracy: -2% -20 mV to +2% + 20 mV

VBE for Darlington (shunted): 0.95 V - 1.80 V (0.75 V - 1.80 V)

base-emitter shunt threshold: 50 kΩ - 70 kΩ

BJT collector test current: 2.45 mA - 2.55 mA

BJT acceptable leakage: 0.7 mA

MOSFET:

gate threshold range: 0.1 V - 5.0 V

threshold accuracy: -2% -20 mV to +2% +20 mV

drain test current: 2.45 mA - 255 mA

gate resistance: 8 kΩ

depletion drain test current: 4.5 mA

JFET drain-source test current: 0.5 mA - 5.5 mA

SCR/Triac:

gate test current: 4.5 mA

load test current: 5.0 mA

diode:

test current: 5.0 mA

voltage accuracy: -2% -20 mV to +2% +20 mV

Vf for LED identification: 1.50 V - 4.00 V

short circuit threshold: 10 Ω

battery:

type: MN21 / L1028 / GP23A 12 V alkaline

voltage range: 7.50 V - 12 V

warning threshold: 8.25 V

dimensions: 103 x 70 x 20 mm (4.1" x 2.8" x 0.8")

Weight per product (nett): 0.098kg (3.5oz)

operating temperature range: 10°C ~ 40°C (50F ~ 104F)

FilerFiler

Kunder som köpte den här köpte ocksåKunder köpte också

  • ESP32-WROOM-32 WIFI/BLE module

      ESP32-WROOM-32 WIFI/BLE module
    ESP32-WROOM-32 is SMD module which you can integrate to your own PCB design. FEATURES ESP32-WROOM-32 contains two low-power Xtensa® 32-bit LX6 microprocessors 448 KBytes ROM for booting and core functions 520 KBytes on-chip SRAM 8 KBytes SRAM in RTC SLOW 8 KBytes SRAM in RTC FAST 1 Kbit of EFUSE, 256 bits MAC WiFi: 802.11 b/g/n/d/e/i/k/r (802.11n up to 150 Mbps) Bluetooth v4.2 BR/EDR and BLE specification Wi-Fi mode Station/softAP/SoftAP+station/P2P Security WPA/WPA2/WPA2-Enterprise/WPS Encryption AES/RSA/ECC/SHA IPv4, IPv6, SSL, TCP/UDP/HTTP/FTP/MQTT Interfaces: SD-card, UART, SPI, SDIO, I2C, LED PWM, Motor PWM, I2S , IR, GPIO, capacitive touch sensor, ADC, DAC, Hall sensor, temperature sensor Operating temperature -40 + 85C Operating voltate: 2.2-3.6V Consumption: 80 mA typ Dimensions: 18 mm x 20 mm x 3 mm
    Art.nr: 41015394
    I lager: 39 
    79.00

  • ESP32-CoreBoard WIFI/BLE development board

      ESP32-CoreBoard WIFI/BLE development board
    ESP32-CoreBoard is easy to prototype development board for the new ESP32 SoC from Espressif, it has dual header pins with 0.1" step which is breadboard friendly. FEATURES WiFi + BLE USB micro connector two buttons status LED 54.32 x 27.9 mm (2.15 x 1.1")
    Art.nr: 41015393
    I lager: 18 
    229.00

  • Batterieliminator 5V 3.1A Micro USB

      Batterieliminator 5V 3.1A Micro USB
    3.1 A for a quick charge directly at the socket 1.5 m charger cable for a sufficient range of movement voltage of 100 - 240 V also allows for use abroad
    Art.nr: 41015349
    I lager: 76 
    149.00

  • Kristall 32.768kHz ø2x6mm

      Kristall 32.768kHz ø2x6mm
    Kvartskristall i hålmonterat utförande. Lämplig för RTC-applikationer. * Frekvenstolerans: ±20ppm * Lastkapacitans: 6pF * Serieresistans: 50kohm
    Art.nr: 41013096
    I lager: 51 
    6.00

  • Batterieliminator 3-12V 300mA stab switchad

      Batterieliminator 3-12V 300mA stab switchad
    Kompakt och funktionell batterieliminator. Ställbar mellan flera olika spänningar och har flera utbytbara kontakter, inklusive en USB-adapter. Batterieliminatorn är mycket strömsnål och drar upp till 90% mindre ström i stand-by än konventionella strömadaptrar och upp till 40% mindre vid drift. Utgången är skyddad mot kortslutning och överström. Specifikationer: Ingång: 100-240VAC Utgång: 3.0, 4.5, 5.0V DC (max 600mA), 6.0VDC (max 500mA), 7.5VDC (max 480mA), 9.0VDC (max 400mA), 12.0VDC (max 300mA) Kontakter: USB-hona, 2.5mm tele, 3.5mm tele, 3.5x1.35 DC-plugg, 5.0x2.1mm DC-plugg, 5.5x1.5 mm DC-plugg, 5.5x2.5mm DC-plugg, 5.5x2.1mm DC-plugg, 4.0x1.7mm DC-plugg Kabellängd: 1.8m Dimensioner: 67 x 39 x 32mm
    Art.nr: 41004810
    Tillfälligt slut
    1 - 89.00
    10 - 80.10
    25 - 66.75

  • Adapterkort SSOP28 - DIL28

      Adapterkort SSOP28 - DIL28
    Adapterkort för att konvertera en SSOP-28 till DIP-28W.
    Art.nr: 41002879
    I lager: 91 
    1 - 49.00
    10 - 44.10
    100 - 36.75