AVR enkortsdatorer

Enkortsdatorer och utvecklingskort baserade på Atmels AVR-processorer. AVR-arkitekturen bestod från början uteslutande av 8-bitarsprocessorer, men finns nu också i 16- och 32-bitars versioner. Processorerna har blivit populära då de är billiga, enkla och har en öppen utvecklingsmiljö.

 

Visar 1 till 12 av 12 produkter
Sortering
 
  • AT90CAN128 Utvecklingskort

      AT90CAN128 Utvecklingskort
    Utvecklingskort för Atmel AT90CAN128. Kortet ger ett enkelt sätt att prototypa med AT90-mikrokontrollern och CAN-BUS. Kortet är extremt kompakt och mäter endast 60 x 55mm men har ändå två D-SUB-kontakter för anslutning till både CAN och RS-232, en JTAG-programmeringskontakt samt 51st GPIO-anslutningar. * Mikrokontroller: AT90CAN128 @ 16MHz * Minne: 128Kb flash / 4Kb EEPROM / 4Kb SRAM * Periferi: CAN, RTC, 4x timers, PWM, 2x UART, I2C, 8x 10bit ADC, SPI * Dimensioner: 60 x 55mm
    Art.nr: 41015247
    I lager: 13 
    299.00

  • ATmega128RFA1 Development Board

      ATmega128RFA1 Development Board
    Utvecklingskort för Atmel ATMega128RFA1, mikrokontroller med integrerad RF-tranceiver. Kortet har samma formfaktor som Arduino UNO och går att använda med shields gjorda för UNO. Processorn levereras med en bootloader som medger programmering via FDTI-kabel och Arduino IDE. RF-tranceivern arbetar på frekvensen 2.4GHz och har en känslighet på 103.5dBm. Processorn stöder Wake-on-Radio, 32-bit MAC symbol counter, temperatursensor, automatiska överföringslägen, 128-bit AES, äkta slumptalsgenerator och höga överföringshastigheter. Kortet levereras utan kontaktdon, så köp till de stift- eller hylslister som önskas. Plats finns även för ett vanligt DC-jack, JST-PH-kontakt för batteri och FTDI-anslutning. Kortet har inbyggd 3.3V-regulator och kan drivas med spänningar från 4.5V till 15V.
    Art.nr: 41012011
    I lager: 5 
    529.00

  • Atmega8U2 Breakout Board

      Atmega8U2 Breakout Board
    The board comes pre-loaded with the SparkFun USB to Serial COM Port firmware. When the board plugs into a USB port, Windows will ask for a driver, point to the driver .inf file found below. The board should now enumerate as a 'SparkFun COM Port' and act the same as the SparkFun FTDI Basic. In other words, you can use it as a USB to serial bridge or you can use it to load code with Arduino. In addition, the pinout on the end of the board is the same as the FTDI Basic, which means you can plug it directly into boards like the Arduino Pro. In addition to the USB to serial firmware, the board also has Atmel's DFU bootloader installed. For information on how to use the bootloader, see the readme file here. You will need to first install Atmel's FLIP software. The bootloader allows you to load your code over USB. See the LUFA project for more example projects. There is also a selectable 3.3V/5V jumper to set the logic level and VCC voltage. Note: If using this board to load code with the Arduino IDE, be sure to select the 'Arduino Pro (5V, 16MHz) w/ATmega328' as the device. If using the DFU bootloader with Atmel's FLIP software, be sure to select the AT90USB82 as the device in FLIP.
    Art.nr: 41004700
    I lager: 3 
    169.00

  • AVR utvecklingskort 20-pin med reläer

      AVR utvecklingskort 20-pin med reläer
    Development board for 20 pin AVR microcontrollers with power supply circuit, crystal oscillator circuit, RS232 port, 10 pin STK ICSP port, 4 relay output, and 4 optocoupler isolated inputs. FR-4, 1.5 mm (0.062"), green solder mask, white silkscreen component print Four mounting holes 3.3 mm (0.13") ICSP 5x2 pin connector for in-circuit programming with AVR Programmers Voltage regulator +5V, 7805 and filtering capacitors Quartz crystal oscillator circuit - 10MHz Reset IC ZM33064 Status LED connected to PB4 Power plug-in jack DIL20 microcontroller socket RS232 DB9 female connector RS232 MAX232 interface circuit with Tx, Rx signals 4 optocoupler isolated inputs with screw terminals Input status LEDs 4 relay outputs with 5A/250VAC contacts with screw terminals Output status LEDs Dimensions: 100x80 mm (3.9x3.15")
    Art.nr: 41003070
    I lager: 3 
    229.00

  • AVR-T32U4

      AVR-T32U4
    ARDUINO Leonardo like board with ATMEGA32U4. Breadboard friendly design. FEATURES ATMEGA32U4 microcontroller, all in one USB communication no need for external FTDI chip. Input power supply taken from mini USB feeds power to the breadboard bus work both on 3.3V UEXT connector which allow many existing modules like RF, ZIGBEE, GSM, GPS to be connected he LEDs and the BUTTONs are on the edge of the board so there is easy access even if the boards have shields on them mini USB connector is used which is common and used in most cell phones, so you do not have to buy other cables
    Art.nr: 41011099
    I lager: 5 
    149.00

  • Cerebot Nano ATmega168

      Cerebot Nano ATmega168
    16KB Flash, 1KB SRAM, 512B EEPROM ESD and short circuit protection for all I/O pins Four small LEDs Small size; 38x20mm IC: Atmel ATmega168 Connector(s): Two 12-pin Pmod One 6-pin Pmod TWI daisy chain 2-pin analog in Programming: Digilent JTAG USB cable or Atmel AVR Dragon The Digilent Cerebot Nano board is useful for embedded control and robotics projects for both students and hobbyists. The Cerebot Nano's versatile design and programmable microcontroller allows you to control different external devices and program the board for multiple uses. The board has many I/O connectors, power supply options, and supports a number of programming tools including ATMEL AVR STUDIO 4, and WinAVR. The Cerebot Nano can be powered either by connecting a 2 x AA battery holder or an externally regulated power supply to J3. Alternatively, a PmodREG1 and a 5V switching power supply can be connected to J1. The Cerebot Nano has a number of connections for peripheral device. Digilent peripheral modules (Pmods) include H-bridges, analog to digital and digital to analog converters, a speaker, switches , buttons, LEDs, RS232 converters, screw terminal connectors, BNC connectors, servo motors and more. For more information see the Peripheral catalogue page at www.digilentinc.com. Note: There are two UART signal pin assignment conventions in use on Digilent products. This product uses the old signal assignment convention. Connecting a product using the old convention with one using the new convention requires the use of a Digilent Pmod Crossover Cable. Click here for a more detailed explanation. NOTE: The Cerebot Nano ships with two straight male and one right angle female 12-pin connectors that are not attached to the board. This allows the greatest flexibility for the user when setting up board usage. The user is required to solder these connectors according to his or her needs.
    Art.nr: 41009997
    I lager: 5 
    174.00

  • Cerebot Plus ATMega2560

      Cerebot Plus ATMega2560
    Kraftfull och månsidig utvecklingsplattform med ATMega2560. Kortet är framtaget speciellt för olika robotikprojekt. Cerebot Plus flexibla design och kraftulla processor låter dig ansluta och kontrollera en mängd olika periferienheter. Via Pmod-kontakterna kan man ansluta Digilients olika periferimoduler, såsom H-bryggor, AD- och DA-omvandlare, högtalare, omkopplare, knappar, lysdioder och olika adapterkort för RS323, skruvterminaler, BNC-uttag, servon, mm. Specifikationer: * ATMega2560 mikrokontroller * 128kB expansionsminne * 8 Servoanslutningar * 11 Pmod-anslutningar * Stöd för AVRISP och JTAG * ESD-skydd för alla GPIOs * 3.3V spänningsregulator
    Art.nr: 41009945
    Tillfälligt slut
    699.00

  • ISP Pogo Adapter

      ISP Pogo Adapter
    Pogo pins make life so much easier when you are trying to program without having to solder a single thing, and when you attach them to an In-system programming (ISP) adapter they become instantly better, this simple kit allows you to do just that. Introducing the ISP Pogo Adapter, a simple and easy way to adapt pogo pins to a 6-pin ISP header allowing you to program an IC still without soldering a header to do so. We've also included a labeled SIP header row and a 6-pin molex cable for you to be able to use your Arduino (or other single-board microcontroller) as an ISP device! This adapter does come as a kit and assembly will be required. Kit Includes: 1x ISP Pogo Adapter PCB 1x Molex Jumper 6 Wire Assembly 1x JST Right Angle Connector 1x Male ISP Header 2x 3/8" Plastic Standoff 4x 1/4" Phillips Head Screw 6x Pogo Pin with Pointed Tip
    Art.nr: 41011873
    I lager: 6 
    109.00

  • OLIMEXINO-32U4

      OLIMEXINO-32U4
    A development board inspired by Arduino Leonardo. FEATURES ATMEGA32U4 microcontroller, all in one USB communication no need for external FTDI chip. Input power supply 7-12VDC ULTRA LOW POWER voltage regulators and the consumption is only few microamps, which enables handheld and battery powered applications. Li-Ion rechargable battery power supply option with BUILD-IN on board charger, so when you attach battery it is automatically charged and kept in this state until the other power source (USB or external adapter) is removed and it AUTOMATICALLY will power the board - no jumpers, no switches! work both on 3.3V and on 5V which is selectable with jumper, so 3.3V and 5V shields can be used UEXT connector which allow many existing modules like RF, ZIGBEE, GSM, GPS to be connected Allows RTC - Real Time Clock (Q1 can be replaced by RTC). NOISE IMMUNE design the LEDs and the BUTTONs are on the edge of the board so there is easy access even if the boards have shields on them all components are LOWER than the connectors, so the shields do not interference with them mini USB connector is used which is common and used in most cell phones, so you do not have to buy other cables original design had flaw and the connectors were not spaced at 0.1" this make perfo board use impossible, to keep the compatibility we have same spacing but we add next to this connector on 0.1" which customer can use with perforated boards all signals on the connectors are printed on top and on bottom of the board, so when you check with probe you know exactly which port you are measuring 4 mount holes make board attachment easier
    Art.nr: 41011097
    I lager: 4 
    149.00

  • Utvecklingskort för ATMEGA16 med 4 reläer

      Utvecklingskort för ATMEGA16 med 4 reläer
    Development board with high power relays, opto-coupled inputs, power supply circuit, crystal oscillator circuit, RS232 port, with ICSP and JTAG ports! JTAG 5x2 pin connector for in-circuit programming with AVR Debuggers ICSP 5x2 pin connector for in-circuit programming with AVR Programmers Pre-mounted ATMega16-16AI Four mounting holes 3.3 mm (0.13") Voltage regulator +5V, 7805 and filtering capacitors Quartz crystal oscillator circuit - 10MHz Reset IC ZM33064 Status LED Power plug-in jack RS232 DB9 female connector RS232 interface circuit with Tx, Rx signals 4 optocoupler isolated inputs with screw terminals Input status LEDs 4 relay outputs with 5A/250VAC contacts with screw terminals Output status LEDs Dimensions: 100x80 mm (3.9x3.15")
    Art.nr: 41003230
    I lager: 2 
    299.00

  • Uzebox AVCore Development Module

      Uzebox AVCore Development Module
    The AVCore is an AVR based, 40-pin DIP, computing module. Onboard is an ATMega644 microcontroller, an Analog Devices AD723 NTSC video encoder, a micro SD card socket, and support circuitry. When combined with the open-source Uzebox kernel, the AVCore can produce full color, NTSC compatible video and audio. The AVCore requires only a 5VDC power input and a connection to a TV or monitor to produce color graphics, text, and multi-voice sound and music. So what do you do with all this power? Check out the SparkFun ESD Attack game! The Uzebox was designed as a simple and low cost game console to help people create their own games. The AVCore's default firmware is programmed in C (using the free AVRWin/GCC tools along with AVR Studio under Windows, or command line utilities under Linux). All audio and video generation is automatically taken care of under interrupt control-- user programs do not need to be concerned with the low-level operation of the system. The AVCore module outputs a composite video signal in addition to s-video (luma/chroma) and analog RGB with separate negative going composite sync outputs. Audio is provided as a line level output. Twenty-one general purpose I/O lines from the ATMega644 are available on the package including SPI, serial (TxD/RxD), INT0, ADCs, and others. The ATMega644 is overclocked to 28.636MHz to provide a significant amount of processing power at a rate compatible with NTSC television signals. Components are mounted on the bottom side of the module to help prevent damage. The Uzebox kernel is capable of producing NTSC compatible video in resolutions up to 240x224 pixels with 256 colors. Sprites, horizontal and vertical scrolling, split screen regions, animation and other effects are all accomplished in software. A four channel wavetable synthesizer is included as well as a PCM audio sample playback mechanism. All audio voices are individually pitch and timbre controllable and mixed with adjustable volume levels in realtime. Simply plug the AVCore into the Uzebox Baseboard and you have the official Uzebox development platform; 100% compatible with the Uzebox specification. Plug the AVCore in to your own design to add high quality audio, video, and micro SD storage to your own project. Note: You must use a regulated 5VDC input for power. Features: ATMega644 Microcontroller 4K of RAM 64K Program Memory 28.61818 MHz overclocked 256 colors with a 3:3:2 color space (RGB) Up to 240x224 resolution 32 simultaneous 6x8 pixels sprites NTSC video out, S-Video, and RGB 4 Channel sound wavetable, 8-bit mono 5VDC power at about 100mA (generating audio and video) micoSD card socket 21 pinouts, see schematic
    Art.nr: 41004272
    I lager: 1 
    599.00

  • Uzebox GameCard Baseboard

      Uzebox GameCard Baseboard
    The Uzebox GameCard baseboard is a carrier board for the AVCore module. The GameCard is designed for creating and playing video games as well as graphic and audio applications based on the Uzebox project. Simply plug the AVCore module into the Uzebox GameCard baseboard and you have the official Uzebox development platform; 100% compatible with the Uzebox specification. The Uzebox GameCard connections include two SNES compatible joypad/controller ports, an S-video jack, RCA jacks with composite video and audio output, an Atmel ISP (2x3 pin) connector, and a 5VDC power input. An LED and pushbutton are available for user programs and a hardwired 'Reset' switch is present for quick restarts on games or debugging. The Uzebox is a retro-minimalist homebrew game console. It is based on an AVR 8-bit general purpose microcontroller made by Atmel. The particularity of the system is that it's based on an interrupt driven kernel and has no frame buffer. Functions such as video sync generation, tile rendering and music mixing is done realtime by a background task so games can easily be developed in C. Features: 2 SNES ports Composite video and audio RCA jacks S-Video (Mini-DIN4) 5VDC power ISP programming header Green LED Reset and user definable switch
    Art.nr: 41004271
    I lager: 2 
    349.00