MikroElektronika

Visar 1 till 12 av 176 produkter
Sortering
 
  10 DOF click
10DOF click är en modul för att känna av rotation, magnetism, acceleration och tryck (10 degrees of freedom). De två chipen, BNO055 och BMP180, ger tillsammans ett gyroskop, accelerometer och magnetometer (3 axlar var) samt en trycksensor. Kortet innehåller även en 32-bit ARM® Cortex®-M0 med sensoralgoritmer från Bosch Sensortec. * Kommunicerar över I2C. * Drivs på 3.3V. * Ställbart omfång för accelerometern: ±2g/±4g/±8g/±16g. 14 bitar. * Gyroskopet är ställbart mellan ±125º/s och ±2000º/s. 16 bitar. * Magnetometerns känslighet: ±1300µT (x, y-axeln), ±2500µT (z-axeln). * Omfång för trycksensorn: 300-110hPa (+9000M till -500M, från havsnivå). * Kompatibel med mikroBUS.
547.00
  3D Hall Click
3D Hall click bygger på hallsensorn MLX90333 (Triaxis) och kan detektera position hos en magnet i närheten. Den ger utslag i X- Y- och Z-led och kan mäta rotation, linjär rörelse och position med hög precision. Eftersom den är kontaktlös är det lätt att skydda den från fukt, damm o.s.v. och har inbyggd signalbehandling för att lättare integreras med en mikrokontroller. Kortet kommunicerar över mikroBUS SPI-interfacet (CS, SCK, MISO, MOSI) och drivs på 5v.
279.00
  4-20 mA R click
4-20mA R Click is an add-on board in mikroBUS form factor which serves as a receiver in a 4-20mA current loop standard. It features INA196 current shunt monitor, MCP3201 12-bit ADC as well as TPS61041 DC/DC boost converter. It receives output current (4-20mA) from transmitter and converts it into a voltage (0.4-2V). This voltage is converted into a 12-bit data signal in the MCP3201 A/D converter and sent via mikroBUS SPI lines. Together with 4-20mA T Click this board forms a complete 4-to-20mA current loop standard. It is designed to use either 3.3V or 5V power supply. The board receives output current (4-20mA) from transmitter and converts it into a voltage (0.4-2V). 3.3V or 5V power supply. Features MCP3201, 12-bit ADC with SPI communication interface. On-board screw terminal for easier connection.
290.00
  4-20 mA T click
4-20mA T Click is an add-on board in mikroBUS form factor. Its a compact and easy solution for adding 4-to-20mA industry standard communication protocol to your design. It features ADuM1411 Quad-chanel digital isolator, MCP4921 12-bit DAC as well as XTR116 4-20mA current loop transmitter. 4-20mA T Click communicates with target board microcontroller via three mikroBUS SPI lines (SDI, SCK, CS). Together with 4-20mA R Click this board forms a complete 4-to-20mA current loop standard. The board is designed to use 3.3V and 5V power supply. LED diode indicates the presence of power supply. The board receives the input digital signal from the microcontroller and sets the output loop current (4-20mA). SPI communication interface. Galvanic isolation provided through ADuM1411 optocoupler. On-board screw terminal for easier connection.
290.00
  4G LTE-E click (Europe)
4G LTE-E click carries the LARA-R211 multi-mode cellular module from u-blox. The board is designed to use 5V power supply. I/O voltage levels could be 3.3V or 5V. It communicates with the target microcontroller over UART interface, with additional functionality provided by the following pins on the mikroBUS line: AN, RST, CS, PWM, INT. With a range of interface options and an integrated IP stack, the modules are designed to support a wide range of data-centric applications. The unique combination of performance and flexibility make these modules ideally suited for medium speed M2M applications, such as smart energy gateways, remote access video cameras, digital signage, telehealth, and telematics. The board has a rich set of components to simplify development: two SMA connectors, a MicroUSB port, as well as a SIM card slot. The LARA-R211 module specifies data rates of up to 10.3 Mb/s for Download, and 5.2 Mb/s for Upload. The network protocol stack includes support for TCP, UDP, PPP, MMS, FTP, SMTP, SMTPS, HTTP, HTTPS, PING, and SSL. It covers following LTE bands: 3, 7, 20. Antenna interfaces - The module has two RF pins with a characteristic impedance of 50 O. The primary antenna pin (ANT1) supports both Tx and Rx, providing the main antenna interface, while the secondary antenna pin (ANT2) supports Rx only for the LTE Rx diversity configuration. A diversity antenna only covers the Rx frequencies, and its job is to acquire an independent sample of data. The application in which you are using the click board can then choose the receive signal it wants to use. u-blox offers m-centre, a free evaluation software for all their cellular modules. It is an easy to use graphical interface where you can configure the module and save the changes on EPROM. You can also view and edit SIM phonebook entries, send text messages, and communicate with the wireless module using AT commands. Simply put 4G is the fourth generation of the cellular network standard. This fourth generation does not support traditional circuit-switched telephony service, but all IP based communication such as IP telephony. If you are not familiar with cellular network standards and protocols and are not sure whether you need GSM or 3G or 4G, read our learn.mikroe.com article about 2G/3G/4G to get a better understanding. LTE or Long Term Evolution, or 4G LTE as it is most commonly called has different categories defined. There are nine different ones so far. LARA-R211 module supports the LTE Cat 1. Key features LARA-R211 cellular module Data rates of up to 10.3 Mb/s for Download Data rates of up to 5.2 Mb/s for Upload Covering the following LTE bands: 3, 7, 20 SMA antenna connectors Micro USB connector Micro SIM card holder UART interface 5V power supply
1 283.00
  7seg click
7seg click is an accessory board in mikroBUS form factor. Its a compact and easy solution for adding 2-digit seven-segment display to your device. It features two 74HC595 8-bit serial-in, parallel-out shift register modules as well as two seven-segment digits. 7seg Click communicates with target board via SPI interface. It has a LED diode (GREEN) that indicates the presence of power supply. SMD jumper is available for selecting whether board will be operating on 3.3V or 5V power supply. Two 7 segment digits on-board. Two 74HC595 serial-in parallel-out shift registers with SPI interface. Board can be operating on either 3.3V or 5V power supply, which is selectable via SMD jumper. Power indicator LED is available on-board.
112.00
  7x10 R click
7x10 R click carries a matrix of 70 red LEDs driven by a pairs of 8-bit serial-in, parallel-out shift registers, a Darlington Transistor array and a Johnson counter. 7x5 is a standard resolution for displaying ASCII characters, so 7x10 click is essentially a dual-character display capable of showing letters in more readable typefaces compared to a 14-segment display. The click communicates with the target MCU through the mikroBUS SPI interface (SCK, SDO, SDI), with additional functionality provided by R CLK, MR#, LATCH and R RST pins. 7x10 R click is designed to use either a 3.3V or a 5V power supply. A pair of red 7x5 LED matrices SPI interface (plus MR#, LATCH and R RST pins) 3.3V or 5V power supply
167.00
  8x8 B click
8x8 B Click is an add-on board in mikroBUS form factor. Its a compact and easy solution for adding 8x8 BLUE LED display matrix to your design. It features MAX7219 8-digit LED display driver module as well as 64 BLUE LED diodes. 8x8 B Click communicates with target board microcontroller via four mikroBUS SPI lines (DIN, DOUT, CLK and CS). The board is designed to use 5V power supply only, but it can be used with 3.3V MCUs as well. The MAX7219 is serial input/output common-cathode display driver with SPI interface. Analog and digital brightness control. On-chip BCD code-B decoder. Board is powered with 5V power supply only, but can be used with 3.3V MCUs as well.
201.00
  8x8 G click
8x8 G Click is an add-on board in mikroBUS form factor. Its a compact and easy solution for adding 8x8 GREEN LED display matrix to your design. It features MAX7219 8-digit LED display driver module as well as 64 GREEN LED diodes. 8x8 G Click communicates with target board microcontroller via four mikroBUS SPI lines (DIN, DOUT, CLK and CS). The board is designed to use 5V power supply only, but it can be used with 3.3V MCUs as well. The MAX7219 is serial input/output common-cathode display driver with SPI interface. Analog and digital brightness control. On-chip BCD code-B decoder. Board is powered with 5V power supply only, but can be used with 3.3V MCUs as well.
167.00
  8x8 R click
8x8 R Click is an add-on board in mikroBUS form factor. Its a compact and easy solution for adding 8x8 RED LED display matrix to your design. It features MAX7219 8-digit LED display driver module as well as 64 RED LED diodes. 8x8 R Click communicates with target board microcontroller via four mikroBUS SPI lines (DIN, DOUT, CLK and CS). The board is designed to use 5V power supply only, but it can be used with 3.3V MCUs as well. The MAX7219 is serial input/output common-cathode display driver with SPI interface. Analog and digital brightness control. On-chip BCD code-B decoder. Board is powered with 5V power supply only, but can be used with 3.3V MCUs as well.
167.00
  8x8 Y click
8x8 Y Click is an add-on board in mikroBUS form factor. Its a compact and easy solution for adding 8x8 YELLOW LED display matrix to your design. It features MAX7219 8-digit LED display driver module as well as 64 YELLOW LED diodes. 8x8 Y Click communicates with target board microcontroller via four mikroBUS SPI lines (DIN, DOUT, CLK and CS). The board is designed to use 5V power supply only, but it can be used with 3.3V MCUs as well. The MAX7219 is serial input/output common-cathode display driver with SPI interface. Analog and digital brightness control. On-chip BCD code-B decoder. Board is powered with 5V power supply only, but can be used with 3.3V MCUs as well.
167.00
  9DOF click
9DOF click carries STs LSM9DS1 inertial measurement module that combines a 3D accelerometer, a 3D gyroscope and a 3D magnetometer into a single device outputting so called nine degrees of freedom data (3-axis acceleration, angular velocity and heading), in 16-bit resolution. 9DOF click communicates with the target MCU through the mikroBUS I2C interface (SCL and SDA) with additional functionality provided by the programmable Interrupt (INT) pin, as well as the Enable (EN) pin. The IC has multiple interrupt lines which can be accessed through jumpers on the click board. I2C addresses are specified in the same manner. The board uses a 3.3 power supply only. 3-axis accelerometer, 3-axis gyroscope and 3-axis magnetometer in one IC Measuring ±2/±4/±8/±16 g acceleration ±4/±8/±12/±16 gauss magnetic ±245/±500/±2000 dps Multiple interrupt lines Selectable I2C addresss Individual sensors can be powered down to reduce consumption Ready-to-use examples save development time
234.00
Sidor: 1 2 3 ... 15