Motor control

Stegmotorstyrning L6470

Part.no: 41010339
Manufacturer: Sparkfun
In stock: 2

Description

STMicro's L6470 (a.k.a "dSPIN") is a 3A, 8-45V bipolar stepper motor driver. It has built-in overcurrent detection, undervoltage detection, overtemperature detection, stall detection, a 5-bit ADC, and a switch input that can be used for either user jog control or as a hard stop function. As if that weren't enough, it also features microstepping support (up to 128 microsteps per full step) and PWM drive voltage limiting.

Unlike most stepper motor drivers, the dSPIN is controlled over an SPI link. It has an on-board 16MHz oscillator which allows it to autonomously execute movement commands. That means no more counting steps in your code! It also supports customized acceleration and deceleration profiles to prevent jerky starts and stops. On-board registers track current speed and location.

This L6470 Stepper Driver Breakout makes it easy to put the dSpin to work in your project. Simply connect your motors and your SPI-capable microcontroller and get steppin'!

The logic supply voltage supports both 3.3V and 5V I/O levels.

Features:

Supports up to 128 Microsteps per Full Step

Over-Temperature Detect

Over-Current Detect

Under-Voltage Detect

PWM Drive-Voltage Limiting

SPI Controlled

On-Board Oscillator and Speed/Location Registers

Stall Detection

5-bit ADC

Preview FilesFiles

Customers Who Bought This Item Also BoughtCustomers Also Bought

  • Hook-up wires w. pins for breadboard - soft 70pcs

      Hook-up wires w. pins for breadboard - soft 70pcs
    Pack of 65pcs jumper wires in assorted lengths and colors. A must in every lab! Fits breadboards. Each cable is terminated with a ø0.5mm pin. Contents: * 45pcs 100mm * 10pcs 150mm * 5pcs 180mm * 5pcs 230mm
    Part.no: 41003181
    In stock: 503 
    Buy
    1 - 29.00
    10 - 26.10
    25 - 21.75
    100 - 17.40

  • LD1117V33 TO-220 voltage regulator 3.3V 0.8A

      LD1117V33 TO-220 voltage regulator 3.3V 0.8A
    Part.no: 40351133
    In stock: 22 
    Buy
    1 - 5.50
    10 - 4.95
    25 - 4.13
    100 - 3.30

  • Flat cable gray 10 wires 1.27 mm /m

      Flat cable gray 10 wires 1.27 mm /m
    10-wire, grey ribbon cable. Conductors: 10 Pitch: 1.27mm (0.05") Color: Grey Length: 30.48m (100ft) Conductor: stranded Size: AWG30 Number of strands per conductor: 7 x 0.127mm Space between the strands of the various conductors: min. 1.27mm Cross section: 156 mil² Insulation: PVC Average insulation thickness: 9mil Min. insulation thickness: 7mil Spark test: 2500V insulation resistance: min. 1Gohm/m Inductance: 1.45mH Impedance: 100ohm Propagation: 4.2ns/m
    Part.no: 31670207
    In stock: 244 
    Buy
    7.43

  • L7805CV TO-220 voltage regulator 5V 1A

      L7805CV TO-220 voltage regulator 5V 1A
    5V voltage regulator in TO-220 package. Max. output current: 1A Thermal- and short circuit protected.
    Part.no: 40350029
    In stock: 58 
    Buy
    1 - 4.00
    10 - 3.60
    25 - 3.00
    100 - 2.40

  • Male header straight 2.54mm 1x40p breakable gold

      Male header straight 2.54mm 1x40p breakable gold
    40-pole male header with 2.54 mm pitch. Can be cut to desired length. Gold-plated pins. Height (frame): 2.54mm Total height: 11.54mm
    Part.no: 41001167
    In stock: 412 
    Buy
    1 - 9.00
    10 - 8.10
    25 - 6.75
    100 - 4.50

  • Arduino Mega ADK rev 3

      Arduino Mega ADK rev 3
    Microcontroller ATmega2560 Operating Voltage 5V Input Voltage (recommended) 7-12V Input Voltage (limits) 5.5-16V Digital I/O Pins 54 (of which 14 provide PWM output) Analog Input Pins 16 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA Flash Memory 256 KB of which 8 KB used by bootloader SRAM 8 KB EEPROM 4 KB Clock Speed 16 MHz Revision 3 of the board has the following new features: 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible both with the board that use the AVR, which operate with 5V and with the Arduino Due that operate with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit.
    Part.no: 41010075
    In stock: 47 
    Buy
    649.00